background image

 

 

3 of 19

1.

 

SAFETY INFORMATION

Due to high temperatures, the appliance should 
be located out of traffic and away from furniture 
and draperies. 
 
Children and adults should be alerted to the 
hazards of high surface temperatures and should 
stay away to avoid burns or clothing ignition. 
 
Young children should be carefully supervised 
when they are in the same room as the appliance. 
 
Clothing or other flammable material should not 
be placed on or near the appliance. 
 
The safety guard must be put back in place prior 
to operating the appliance if it has been removed 
for servicing or cleaning. 
 
This appliance should be installed and repaired 
by a qualified service person. 
The appliance should be inspected before use and 
at least annually by a professional service person. 
More frequent cleaning may be required due to 
excessive lint from carpeting, bedding material, 
etc. It is imperative that control compartments; 
burners and circulating air passageways of the 
appliance are kept clean. 
 
Keep curtains, clothing, furniture and other 
flammable materials a safe distance from all 
parts of the appliance 
 Keep the appliance area well clear and free from 
combustible materials, gasoline and other 
flammable vapours and liquids. 

If any changes are made to the room construction 
in the vicinity of the appliance after installation 
(e.g. additional mantle etc.) make sure that the 
changes conform to the installation requirements 
in this manual. 
 
Never attempt to burn paper or any other 
material in the appliance. 
 
This appliance must be properly connected to a 
venting system. The venting system should be 
checked periodically. Recent trends in home 
improvement and new tighter construction 
techniques have contributed to problems with 
venting. If you suspect that your appliance is not 
venting properly, do not operate. Seek expert 
advice. 
 
Do not use this appliance if any part has been 
under water. Immediately call a qualified service 
technician to inspect the appliance and to replace 
any part of the control system and any gas 
control, which has been under water. 
 
Only trim kits supplied by the manufacturer shall 
be used in the installation of this appliance. 
 
Draft openings must not be covered or blocked 

 

Should you encounter an operation problem, call 
your dealer immediately. Do not try to repair the 
unit as you may cause an injury or damage the 
fireplace. 

 

 

NOTE 

When operating your new fireplace for the first time, some vapors may be released due to the burning of curing compounds 
used in the manufacture of the appliance. They may cause a slight odor and could cause the flames to be the full height of the 
firebox, or even slightly higher, for the first few hours of operation. It is also possible that these vapors could set off any 
smoke detection alarms in the immediate vicinity. These vapors are quite normal on new appliances. We recommend 
openning a window to vent the room. After a few hours use the vapors will have disappeared and the flames will be at their 
normal height.   
During the first hour of use the ceramic firebox walls may go a smoky color. This is not soot. It is a temporary effect lasting 
only while the ceramic material becomes stabilized. The walls will revert to their initial color after your fire has been used for 
one or two hours.     
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание PORTRAIT 922ECN




















Отзывы: