Valor PORTRAIT 922ECN Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 19

background image

12 of 19

11.

CERAMIC FUEL BED INSTALLATION

11.1.

Ceramic Walls Installation

1.

Locate the ceramic rear wall on top of the base coal support as shown in fig 12.

2.

Insert the right hand sidewall at approx 30 degree angle between the firebox side and the burner. Swing the top of the

sidewall to the vertical position and locate behind the upper baffle (see fig13).

3.

Repeat step 2 with left hand sidewall (Fig 13)

Fig 12 Back Brick Installation

Fig 13 Side Brick Installation

«
...
10
11
12
13
14
...
»

Содержание PORTRAIT 922ECN




















Отзывы:

Нет отзывов

Похожие инструкции для PORTRAIT 922ECN

Бренд: Verine Страницы: 19

Heatilator Icon Series

Бренд: Heatilator Страницы: 2

high country nz3000h

Бренд: Napoleon Страницы: 128

Duraflame DFI030ARU

Бренд: Twin-Star International Страницы: 26

Бренд: Napoleon Страницы: 60

Бренд: RealFlame Страницы: 63

Бренд: Boulevard Страницы: 64

Torch GSST8N and

Бренд: Napoleon Страницы: 16

Бренд: Faber Страницы: 40

SANDBANKS YD-SD5PC

Бренд: Canvas Страницы: 20

Бренд: Home Decorators Collection Страницы: 25

Бренд: Room&Board Страницы: 30

Бренд: RUSTA Страницы: 36

Symmetry RDV3600

Бренд: Rinnai Страницы: 20

Бренд: Paramount Fitness Страницы: 15

Бренд: Paramount Fitness Страницы: 18

focus rs plus remote

Бренд: Paragon Fires Страницы: 28

Бренд: Focus Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды