Valor Legend 936XN Скачать руководство пользователя страница 1

Страница: 1 / 21

Legend

stove

Models

936XN

(Natural Gas)

936XP

(Propane)

FREESTANDING DIRECT VENT GAS FIREPLACE

HEATER

INSTALLATION

AND OWNER’S

MANUAL

For Pedestal base with

Contemporary front

Legs with Traditional front

Please read this manual
before installing and
operating.

Vous pourrez vous procurer un exemplaire en langue Française de cette brochure chez votre concessionaire.

600B133/01

- Do not store or use gasoline or other

flammable vapors and liquids in the vicinity
of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not
use any phone in your building.

•

Immediately call your gas supplier from a
neighbor’s phone. Follow the gas
supplier’s instructions.

•

If you cannot reach your gas supplier, call
the fire department.

- Installation and service must be performed by

a qualified installer, service agency or the gas
supplier.

WARNING: If the information in this
manual is not followed exactly, a fire or
explosion may result causing property
damage, personal injury or loss of life

This appliance may be installed

permanently located,

manufactured (mobile) home,
where not prohibited by local

codes.

This appliance is only for use

with the type of gas indicated on

the rating plate. This appliance

is not convertible for use with

other gases, unless a certified

kit is used.

This appliance is a domestic room

heating appliance. It must not be

used for any other purpose such

as drying clothes etc.

Содержание Legend 936XN






















Результаты поиска

Содержание Legend 936XN

Отзывы:

Похожие инструкции для Legend 936XN

Бренды по названию

Популярные бренды

Valor Legend 936XN, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Legend 936XN

Отзывы:

Похожие инструкции для Legend 936XN

Бренды по названию

Популярные бренды