Valor Homeflame Dream Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 66

Valor Homeflame Dream Скачать руководство пользователя страница 24

INSTALLER GUIDE

Page 24

9.

There is a length of self adhesive foam seal supplied with the fire. This will need to

be fitted to the outer rear edges of the side and

top flanges of the convector box. Cut a 485mm

length of foam seal. Be careful not to stretch the

seal when measuring. Remove the protective

backing from the foam seal and fit this to the rear

of the top flange (See figure 17). Cut two 580mm

lengths. Fit these to the rear outer edges of the

side flanges. Ensure that there is no gap

between the foam seals where they meet at the

top flange (See figure 17).

9. CONVECTION BOX INSTALLATION

9.1 Method 1 - Front fixing to fireplace surround.

1.

Make sure that the fireplace front surround area is

sound enough to take the fibre / wooden plugs and

woodscrews. If necessary, make sound with suitable

cement.

2.

Place the convection box centrally in the fireplace

in the position in which it is to be permanently

installed. If a concealed connection is being used,

insert the convection box into the fireplace feeding

the supply pipe through the pierced hole in the rear

grommet.

3.

Mark the fireplace front surround through the four

fixing holes in the side flanges of the convection box

(See figure 18).

© GDC Group Ltd. 2012

Figure 17. Fitting the foam seal

Figure 18. Front fixing

«
...
22
23
24
25
26
...
»

Содержание Homeflame Dream



































































Отзывы:

Нет отзывов