background image

INSTALLER’S GUIDE

Page 15

7   C E R A M I C   C O A L S   I N S T A L L A T I O N

7.1

Place the

front base coal in
the burner
compartment so
that it rests on the
ledges at the sides
and front. Pull the coal forward so that it
is immediately behind the front rim of the
burner compartment See figure 15

.

7.2

Place the

rear base coal
in the burner
compartment
behind the
front coal. It
should rest
on the ledge
at the back of
the burner
compartment.
The
projections at
the sides of
the rear coal
should touch the front coal. See figure 16.

7.3

Place

one of the
loose coals
from the bag
in the centre
of the front
base coal.
Make sure
that it bridges
the space between the front and rear base
coals. See figure 17.

7.4

Place

two coals
each side
of the
centre
loose coal.
Make sure
that they
bridge the space between the front and
rear base coals. See figure 18.

7.5

Place a

loose coal
behind the
central coal
in the front
row central
and resting
on the two peaks of the rear base coal. See
figure 19.

7.6

Place

two coals
each side of
the centre
loose coal
and
immediately
behind the
front row of
coals. See
figure 20.

7.7

Place

two of the
remaining coals each side of the central
peak at the rear of the base coal and
immediately behind the second row of
coals. See figure 21.

Fig.21

Fig. 20

Fig. 19

Fig. 18

Fig. 17 First loose coal

    

Fig. 16 Rear base coal

Fig. 15 Front base coal

Содержание COALFLAME BR627



























Отзывы: