background image

Page 1 of 14 

GEN2-V1 10-ft Instructions (Generic) doc:r1 

 
 

RETRACTABLE PATIO SHADE AWNING 
Patio Awning Guide-8ft.

 

x10ft.

(Proj. X Width)

 

Model: APR-100810***/APR-60020810 (version: GEN2-V1) 

 

 
 

1. INTRODUCTION: 

Thank you for purchasing a Retractable Shade Awning

.

 Before proceeding, please ensure that all the parts are in 

the box, as listed below: 
 

Master Carton Contents: 

 

 

 

 

 

1-Box 

labeled EXTENSION ARMS 

1-Box 

labeled LEFT WALL BRACKET ASSEMBLY 

1-Box 

labeled RIGHT WALL BRACKET ASSEMBLY 

1-Box 

labeled GEAR MECH. & Support Bracket 

1-EA 

150 cm Roller Tube, w/Square Drive 

1-EA 

150 cm Roller Tube, w/Round Drive 

1-EA 

50 mm Roller Tube Joiner 

1-EA 

150 cm Valance Tube, drilled left 

1-EA 

150 cm Valance Tube, drilled right 

1-EA 

50 mm Valance Tube Joiner, drilled 

3-PCS 

312cm Plastic Spline (coiled) 

1-BAG 

Bubble Bag, labeled MISC. PARTS, includes: 
-2-Wrist Assemblies 
-2-Position Poles 
-Level 
-6-Spline Stops 
-Right & Left Valance Tube End Caps 
-2-Bags of 4-pcs 

1/2” x3” Sleeve Anchors 

1-EA 

160 cm Crank Handle 

 
In the event that there is ANY part missing or damaged, please 

DO NOT RETURN THE PRODUCT TO YOUR 

RETAILER

. By returning the product to your retailer we can not assist you in getting your awning properly installed. 

Call our TOLL FREE Customer Service Hotline at 1-888-875-4844 for parts or replacement of parts that may have 
been damaged when shipped. 
 
You may also go to our website a

www.valor.ca

  in the Valor Shade/Patio Awning section for all assembly and 

installation instructions, set up, adjustment, and troubleshooting instructions. There you will be able to see common 
problems and how to rectify them usually with a simple adjustment. You may also use this section to email us your 
questions, and during business hours between 9:00 AM and 4:00 PM EST you will be able to connect with a 
customer service representative for assistance. 

 
2. PRODUCT: 

The Valor Shade Awning is a unique program that allows you to order awnings that are modular in design making 
them easier to transport . The product is offered with your choice of several available patterns (sold separately). The 
product is factory configured with Left Side operation (when facing the house), but can be converted to right side 
operation by following the steps outlined in this guide. 

 
IMPORTANT WARNING: 

Your new awning is intended as protection against the sun only. It is not to be used during periods of strong 
wind, rain, hail, or snow. The warranty will not cover use during these periods. Bird droppings, pine needles, 
and various air born materials that may settle on your awning; awning fabric should be cleaned using water 
and a light soap. No abrasive cleansers or harsh chemicals should be used on the fabric. Damage to the 
Awning (including the fabric) from any foreign material is not covered under our warranty. 

WARNING: 
DO NOT CUT THE PLASTIC ZIP TIES ON THE AWNING EXTENSION ARMS UNTIL INSTRUCTED TO 
DO SO IN THIS GUIDE. THE FOLDING ARMS ARE UNDER SPRING TENSION AND SHOULD NOT BE 
CUT UNTIL THE AWNING IS FULLY ASSEMBLED AND INSTALLED ON THE WALL.

 

Содержание APR-100810 Series















Отзывы: