Valor 739-72ILN/P Скачать руководство пользователя страница 6

Страница: 6 / 34

Owner’s Information

1. Inspect and operate the pressure relief mechanism to verify relief mechanisms are free from obstruction

to operate—see

Cleaning Your Fireplace: To re

t the window

section of this manual.

2. Clean glass window with a suitable ﬁ replace glass cleaner. Abrasive cleaners must not be used. Be

careful not to scratch the glass when cleaning—see

Cleaning Your Fireplace

section of this manual.

3. Inspect the operation of the ﬂ ame safety system Pilot or Flame rectiﬁ cation device.

4. Inspect and ensure the lighting of the main burner occurs within 4 seconds of the main gas valve

opening. Visual inspection should match that outlined in the appliance instruction manual. Inspect
primary air openings for blockage—see

Checking Pilot and Burner Flame

section of this manual.

5. Inspect condition of vent and vent terminal for sooting or obstruction and correct if present.

6. Vacuum and clean any debris in the ﬁ rebox that is not supposed to be there.

7. Test and measure the ﬂ ame failure response time of the ﬂ ame safety system. It must de-energize the

safety shutoﬀ in no more than 30 seconds.

8. Check all accessible gas-carrying tubes, connections, pipes and other components for leaks—see

Set up

Gas Supply

section of this manual.

Annual Inspection

In order to maintain the safe operation of your ﬁ replace,
contact your dealer to have a qualiﬁ ed technician go
over the list below and make the necessary veriﬁ cations
at least once every year.

Annual Inspection List for a Safe Operation—to be performed by a qualiﬁ ed technicien only

OWNER’S
INFORMATION

Содержание 739-72ILN/P



































Результаты поиска

Содержание 739-72ILN/P

Отзывы:

Бренды по названию

Популярные бренды

Valor 739-72ILN/P, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 739-72ILN/P

Отзывы:

Бренды по названию

Популярные бренды