Valor 700 Скачать руководство пользователя страница 2

2

When the pilot is off, it will take 2 
minutes before it can be lit again.

TO TURN ON APPLIANCE

TO TURN OFF APPLIANCE

FLAME HEIGHT ADJUSTMENT

•• 

On the valve, turn MAN knob on the ON, full 
counterclockwise             position.

•• 

Place ON/OFF switch (if equipped) in I (ON 
position).

STANDBY MODE (Pilot Flame)

•• 

Press and hold       (small 

 ame) to set appliance at 

pilot 

 ame.

•• 

Simultaneously press the OFF and
     (large 

 ame) buttons until a short 

beep con

 rms the start sequence 

has begun; release buttons.

•• 

Continuing beeps con

 rm the 

ignition is in process.

•• 

Once pilot ignition is con

 rmed, 

there is main gas 

 ow.

•• 

After main burner ignition the 
handset will automatically go into 
manual (MAN) control mode.

•• 

Press OFF button.

When the pilot is off, it will take 2 
minutes before it can be lit again.

•• 

In standby mode: Press and hold
     (large 

 ame) button to increase 

 ame height.

WARNING

When pilot ignition is con

 rmed, motor turns 

automatically to maximum 

 ame height.

Remote Control Operation

NOTE: Before using the remote control system for 
the 

fi

 rst time, 

the receiver and the handset must be 

synchronized. See the section

 Remote Control Initial 

Set-up

 on the previous page of this manual. 

Set

 (scrolls

through

modes and

settings)

OFF

 (returns

 to set mode,

turns the burner

 and the pilot off)

Large flame 

button (flames

up, sets hours,

temperature)

Small flame 

button (flames

down and off, 

sets minutes, 

temperature)

Current 

temperature

(F or C)

Current time 

(12 or 24 hour clock)

Modes (Manual, 

Temperature, Timer)

Handset 

sensor

Battery status

Current

 programmed

 period (Timer)

Period 

start or end 

(Temp, Timer)

Fan setting (if used)
Burner setting

Display Overview

Handset Overview

Note: In the TEMP or TIMER modes, the remote 
handset senses the room temperature and adjusts the 

 ame accordingly. 

To communicate, the handset should be within 15 feet 
(4.5 meters) of the 

 replace. 

Do not leave the handset on the mantel or hearth.

IMPORTANT:

 

BEFORE YOU BEGIN, please note that 

on this system, the settings of time, temperature and 
automatic ON/OFF 

can only be programmed when 

the function display is 

fl

 ashing

. Be patient when 

programming as it can take a few seconds to set.

Содержание 700








Отзывы: