background image

1 of 18 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

530 B Vent 
GAS FIREPLACE HEATER

 

 

INSTALLATION BOOKLET 

Manufactured by 

MILES INDUSTRIES LTD. 

British Columbia, Canada 

• 

SAFETY 
INFORMATION 

• 

LOCATION 

• 

SUPPLY GAS 

• 

PACK CONTENTS 

• 

APPLIANCE 
PREPARATION 

• 

VENTING & 
APPLIANCE FIXING 

• 

FITTING SIDES & 
SWITCH 

• 

GAS SUPPLY 
INSTALLATION 

• 

AERATION SETTING 
CHECK 

• 

CERAMIC FUEL BED 
INSTALLATION 

• 

WINDOW REFITTING 
& CHECKING 

• 

OPERATION CHECKS 

• 

INSTALLATION 
COMPLETION

 

 

600B185-2 

 
 
 
 
 

- Do not store or use gasoline or other flammable 
vapors and liquids in the vicinity of this or any other 
appliance. 
 
-WHAT TO DO IF YOU SMELL GAS 
 

• 

Do not try to light any appliance. 

• 

Do not touch any electrical switch: do not use  

      any phone in your building. 

• 

Immediately call your gas supplier from a  

      neighbor’s phone. Follow the gas supplier’s  
      instructions. 

• 

If you cannot reach your gas supplier, call the 

      fire department. 
 
- Installation and service must be performed by a 
qualified installer, service agency or the gas 
supplier. 

 

WARNING:    If  the  information  in  these 
instructions  is  not  followed  exactly,  a  fire  or 
explosion  may  result  causing  property  damage, 
personal injury or loss of life.
 

This appliance is a domestic room heating 
appliance. It must not be used for any other 
purpose such as drying clothes etc. 

 

This appliance is suitable for installation 
in a bedroom or bed sitting room. 

 

Содержание 530 B Vent



















Отзывы: