background image

13

© Vallox Oy - All rights reserved

CLEANING THE HEAT RECOVERY CELL

Check that the heat recovery cell is clean roughly once a year, 

or whenever the filters are being replaced. Clean by washing 

as required.

IMPORTANT

If the unit has an enthalpy cell, it must not be washed. 

Only aluminium or plastic cells can be washed.

To check and clean the heat recovery cell:

1.   Disconnect the ventilation unit from the mains electricity 

supply.

2.   Lift the latch to open the door of the ventilation unit and 

lift the door off.

CAUTION

The door is heavy.

3.   Remove the filters (A, B, C).

4.  Remove the sealing strip (E) above the cell in the direction 

of the arrow.

5.   Lift and pull the cell (D) out of the unit.

IMPORTANT

Handle the cell carefully! For example, do not lift the 

cell by the layers. The cell layers are very thin and 

easily damaged.

6.   If the cell is dirty, clean it by immersing it in warm water, 

to which a small amount of a mild detergent has been 

added.

7.   Rinse the cell clean with a water spray. Do not use a high-

pressure cleaner.

8.   When all the water has drained from between the layers, 

reassemble the ventilation unit in the reverse order.

9.   Close the door and ensure that the safety switch catch of 

the door is engaged.

10.  Plug the ventilation unit back into the mains. The heat 

recovery cell has now been checked and cleaned.

MAINTENANCE

D

E

D

E

CONDENSING WATER

In the heating season, the extract air humidity condenses to 

water. In new buildings, condensation runoff can form rapidly. 

Condensed water must be able to freely leave the unit. 

At some time before the heating season begins (e.g. during 

autumn maintenance), check that the siphon or the condensing 

water outlet in the bottom pool are not clogged. To check this, 

pour some water into the pool. Clean as required.

NOTE

Some condensing water 

may have accumulated 

in the bottom pool 

of the unit; this is 

normal and requires no 

corrective action. 

WARNING

Water must at all times 

be kept out of the 

electrical system.

Содержание Vallox 90 MV





























Отзывы: