Valley-Dynamo Jet-Pong Coin JP100 Скачать руководство пользователя страница 76

Страница: 76 / 80

73 |

P a g e

Symptom #13: Credit Counter Faulty

CAUTION:

This procedure requires the power to be on and the lid opened. When lifting the lid attach the Prop

Stick as a safety measure. (*CE Tables only)

1) Open the Coin Mech Door. Check the wiring connections and harness from the mechanical counter to the

PLC Carrier Board.

Symptom #14: Ticket Dispenser(s) Faulty

CAUTION:

This procedure requires the power to be on and the lid opened. When lifting the lid attach the Prop

Stick as a safety measure. (*CE Tables only)

1) A warning message will display on the HMI Touch Screen when one or both ticket trays are empty:

2) Use the troubleshooting screen to test the Ticket Dispenser. See instructions earlier in this chapter for

details.

3) If the tray is not empty check all connections and cable harness to/from the Ticket Dispenser. There

should be 12Vdc power at the connector to the Ticket Dispenser.

4) Check the ticket dispenser to make sure there are tickets available and that there are no jams. You may

need to remove the Control Console by removing the screws around the perimeter of the black plastic.
There is a button on the ticket dispenser to manually feed tickets.

Содержание Jet-Pong Coin JP100

















































































Результаты поиска

Содержание Jet-Pong Coin JP100

Отзывы:

Похожие инструкции для Jet-Pong Coin JP100

Бренды по названию

Популярные бренды

Valley-Dynamo Jet-Pong Coin JP100, Руководство пользователя

Результаты поиска

Содержание Jet-Pong Coin JP100

Отзывы:

Похожие инструкции для Jet-Pong Coin JP100

Бренды по названию

Популярные бренды