![background image](http://html.mh-extra.com/html/valex/mmiscel/mmiscel_instruction-manual-and-safety-instructions_851002010.webp)
- 10 -
- That the ambient temperature is between 10 ° and 35 °C.
- That the environment is not in the atmosphere of flam-
mable/explosive.
Remove the machine and check the components and
their visually perfect integrity at this point proceed to a
thorough cleaning to remove any protective oils used for
transportation.
HANDLE SIDE OR REAR HANDLE ASSEMBLY (pos.3-4,
if any)
If the unit is equipped with handles additional (in addition to
main pos.2), install one of the handles on the machine pos.4
or pos.3 observing the fig.C. Never mount at the same time
both the handles pos.3 and 4.
MOUNTING OF THE SPINDLE (fig.E, if any)
Screw the spindle shaft of the mixer. Fix the spindle screwing
counterclockwise the screw.
MOUNTING ADAPTER (fig.F, if any)
Screw the adapter (pos.13) onto the shaft of the mixer using
the supplied keys.
MOUNT WHIP MIX (pos.10)
!
!
WARNING! During the assembly and dismantling of
the whip unplug it from the power outlet.
Install the whip mixing and at the end remove all the keys
and check that the hose is centered and tight.
STARTING AND STOPPING
!
!
WARNING! Before starting the power tool is required
to wear safety glasses, gloves, hearing protection (not
included).
!
!
WARNING! When using make sure that no one comes
to your area of work.
Starting
1) Insert the plug into the power outlet
2) Firmly grasp the handles (pos.2-3-4) with both hands
3) Start press in sequence the security (pos.8 if any) and
the switch (pos.1).
The switch is of the type “Maintained action “ and therefore
the power tool will remain lit for as long as you hold the
switch.
Stopping
To stop the device, release the switch.
Continuous operation (if present)
For continuous operation is necessary, after the steps of
“Starting”, press the button (pos.8) to lock the switch.
Then, to stop the machine, press the switch (pos.1) and
then release it immediately.
!
!
WARNING! When you work with the switch in conti-
nuous service, never leave your grip on so that, in case of
danger, you can stop the machine immediately.
We recommend that you repeat these steps a few times
before starting the work in order to familiarize yourself with
the controls as much as possible.
If you look malfunctions turn off the power tool and refer to
the chapter “Problems, Causes and Remedies”
When you do not work turn off and unplug it from the outlet.
INSTRUCTIONS FOR USE
After having read the previous chapters, read carefully these
tips that will allow you to get the maximum performance.
Take your time to get familiar with all the controls and only
after you have gained a good experience to be able to exploit
fully its potential.
ELECTRONIC SPEED SPINDLE (if present)
Turn the wheel (pos.6) till it reaches the desired speed.
SPINDLE SPEED MECHANICAL ADJUSTMENT (if present)
!
!
WARNING! The selection operation speed must be
performed with the tool is switched off and the spindle
stopped .
Moving the selector switch (pos.7) in one of two positions
you can select the desired speed mechanically.
ADJUSTING THE DIRECTION OF ROTATION OF CHUCK (if
present, fig.D)
!
!
WARNING! The operation of reversing the direction
of rotation must be performed with the tool is switched
off and the spindle is stopped .
Look carefully at the fig.D.
WHIPS MIXING
!
!
WARNING! Observe the max. diameter specified in
the technical data.
Buy quality whips, with an attachment suitable to the cha-
racteristics of the spindle or the adapter (fig.G), the direction
of rotation and adapted to the material to be mixed. Please
contact your dealer who will advise you.
Our company offers a wide range of hoses suitable for the
most diverse applications.
OPERATION OF MIXING
Prepared separately mix the materials, which must be contai-
ned in a large container and sufficiently stable, so as to avoid
splashes or rotates under the effect of rotation of mixing; in
addition, check that there are no impurities such as stones,
wires, bollards etc. .
For no reason the material such as water or other liquids
must not come into contact with the power tool, the only
part of the whip is permitted.
Assume a stable position with legs slightly apart, with mixer
disposed vertically above the container, the hands must
firmly grasp both handles.
Attention! Start only if the hose is inside the container and
immersed in the material to be mixed.
Attention! During use, do not put your hand into the con-
tainer. Operate the mixer with caution, keeping away from
the legs, from clothing and the power cord.
For blender with a reversal of the direction of rotation: ac-
cording to the type of whip (clockwise or counterclockwise)
to select the correct direction of rotation.
For mixer equipped with adjusting the speed of rotation:
started working with a low speed and then increasing it
as necessary.
When mixing, do not hit with a whip container of the material.
At the end turn off the mixer and remove it from the material.
Содержание MMiscel
Страница 12: ......