PAGE 7
www.veebee.com.au
each corresponding hole in the frame.
To remove the bumper bar: reverse the
above steps. Always test that bumper bar is
securely engaged before use.
7>HANDLE BAR
To adjust the handle bar height, press
and hold the buttons on either side of the
handle bar while raising or lowering.
8>BRAKE
To engage the brake, simply push the red
brake pedal down (the one brake pedal
engages both brakes.) To disengage the
brake, lift the red brake pedal upward.
WARNING: ALWAYS BE SURE BOTH
WHEEL BRAKES ARE ENGAGED
WHEN THE STROLLER IS AT REST.
9>TO FOLD YOUR STROLLER
Remove the child from the seat. Incline the
seat and fold the hood. Press the release
button on the right hand side of the real leg
to release the main lock.
Locate the pull strap found in the centre of
the seat pocket and pull upwards on the
pull strap with a gentle tug, Your stroller
will fold in half. Ensure that the frame lock
is engaged.
ALWAYS ENGAGE THE FRAME LOCK
WHEN FOLDED. TAKE CARE WHEN
LIFTING THE STROLLER TO KEEP YOUR
KNEES BENT AND BACK STRAIGHT. DO
NOT CARRY THE STROLLER BY THE HOOD,
BUMPER BAR OR THE REAR BRAKE AXLE.
10>SEAT RECLINE
To lower the seat: Pinch the clamp behind
the seat and slide it down to the desired
position. Pull the seat down on both sides
to match the recline position of the clamp.
To raise the seat; lift the seat and hold
at the desired position. Pinch the clamp
behind the seat and slide it up to the
desired position.
NOTE: ALWAYS TEST THAT THE
SEAT IS SECURELY FIXED IN
POSITION BEFORE USE. SPECIAL CARE
MUST BE TAKEN WHEN ADJUSTING THE
SEAT POSITION WITH A CHILD IN THE
STROLLER.
11>FOOTREST
To adjust your footrest downward, press
the buttons on each side of the footrest
while simultaneously pressing down lightly
on the footrest.
To raise the footrest, simply lift it with your hand.
12>HARNESS
Your stroller harness is specifically
designed with many built in safety features.
This includes the requirement that, when
opened, all straps are released so that no
dangerous loops can be formed causing a
strangulation hazard.
WARNING: YOUR CHILD MUST
ALWAYS BE HARNESSED WHEN IN
THE STROLLER
Closing your harness: Slide each of the
shoulder strap bottom guides (a) into the
corresponding channel on the top of each
side strap prong. Insert each completed
prong into the central buckle housing (b).
Carefully adjust the harness straps to snugly
fit your child by adjusting the sliders (c)
located on each strap. The harness should
be fitted to your child’s body, tight enough
so that they cannot wriggle free of the straps
but, loose enough, so as not to cause any
discomfort.
For even more flexibility, the height at
which your shoulder straps are fitted to the
stroller can be adjusted at 3 points(d).
To change the shoulder strap position:
Open the harness. Re thread the shoulder
strap back through the desired loop on the
front of the seat
Opening your harness: Press the central
housing button (e). This will release both
side prongs from the central housing.
The shoulder and waist straps will release
automatically from each other.
If the shoulder and waist straps do not
automatically disengage from each other,
manually slide the guides of the waist
channels. Your harness will separate into
5 sections.
IMPORTANT WARNING: WHEN NOT
IN USE, BE SURE THE SHOULDER
AND WAIST STRAPS ARE ALWAYS
DISCONNECTED FROM THE CENTRAL
HOUSING AND EACH OTHER
13>TETHER STRAP
WARNING: USE THIS STRAP TO
STOP THE PRAM/STROLLER
ROLLING AWAY.
DashIM_190718.indd 7
19/7/18 4:20 pm
