manualshive.com logo in svg

Val-Tex Easy Lube 40-70, Руководство по эксплуатации

Поделиться
Скачать
Val-Tex Easy Lube 40-70 Скачать руководство пользователя страница 35

SER 331378-A1

High-Pressure Stripped Pump

Revision (2-98)

12

Alemite Corporation

Troubleshooting Chart

Pump Indications

Possible Problems

Solution

Pump does not cycle

1. Air motor not operating properly

2. Pump tube jammed and/or contains loose 

components

3. Insufficient air pressure

1. Inspect air motor and rebuild or 

replace as necessary

2. Rebuild pump tube

3. Increase air pressure

Pump will not prime

1. Excessive cycling speed
2. Pump leaking internally

1. Reduce air pressure
2. See Internal Leaks

Pump cycles rapidly

Product source empty

Replenish product

Pump cycles continuously, or 
slowly (once or twice/hour)

1. Pump leaking internally 
2. Pump leaking externally
3. Distribution system leaking

1. See Internal Leaks
2. See External Leaks
3. Correct leak

External Leaks

Product leakage visible at top 
of Adapter (5)

1. Initial tightening of Adapter (5) to Air 

Motor Assembly (3) not sufficient

2. Damaged O-Ring (4)

1. Tighten Adapter (5) into Air Motor 

Assembly (19)

2. Replace O-Ring (4)

Product leakage visible at top 
of Follower Tube (33)

1. Initial tightening of Tube (18) to Adapter 

(5) not sufficient

2. Initial tightening of Tube (18) to 

Retainer (20) not sufficient

3. Initial tightening of Extension (24) to 

Retainer (20) not sufficient

4. Initial tightening of Extension (24) to 

Primer Body (35) not sufficient

5. Gasket(s) (6) worn or improperly 

crushed

6. Gasket (23) worn or improperly crushed

1. Tighten Tube (18) into Adapter (5)

2. Tighten Tube (18) into Retainer (20)

3. Tighten Extension (24) into

Retainer (20)

4. Tighten Extension (24) into Primer 

Body (35)

5. Replace Gasket(s) (6)

6. Replace Gasket (23)

Product leakage visible at 
bottom of Follower Tube (33)

Damaged O-Ring (34)

Replace O-Ring (34)

Internal Leaks

Pump does not prime or 
cycles continuously, or slowly 
(once or twice/hour)

1. Foreign material between Ball (15) and 

seat in Piston (17)

2. Foreign material between Valve 

Body (27) and Valve Seat (28)

3. Worn or damaged Ball (15)
4. Worn or damaged Piston (17)
5. Worn or damaged Spring (14)
7. Worn or damaged Valve Body (27)
8. Worn or damaged Valve Seat (28)
9. Worn or damaged Seal (21)

10. Worn or damaged Seal (26) 
11. Worn or damaged Rod (29)

1. Locate and eliminate source of 

foreign material.

2. Disassemble pump tube, clean, 

inspect, and replace worn or 
damaged components.

Changes Since Last Printing

Added Models 331378-E1, F1, and H1

Содержание Easy Lube 40-70










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды