manualshive.com logo in svg

Val-Tex Easy Lube 40-70, Руководство по эксплуатации

Поделиться
Скачать
Val-Tex Easy Lube 40-70 Скачать руководство пользователя страница 34

High-Pressure Stripped Pump

SER 331378-A1

Alemite Corporation

11

Revision (2-98)

Bench Test

  1. Make sure air pressure at the regulator reads zero.

  2. Install air Connector (4) to the inlet of the air motor.

  3. Connect Air Coupler (5) to the Connector.

  4. Slowly supply air pressure [not to exceed 20 psi 

(1.4 Bars] to the pump’s motor.
• The pump assembly should cycle.

If the pump assembly does not cycle, refer to the 

Troubleshooting Chart for details.

With air pressure at zero:

  5. Connect a product hose to the pump’s material outlet. 

• Direct the hose into an appropriate collection 

container.

  6. Place the pump in grease.

  7. Slowly supply air pressure to the pump’s motor.

  8. Allow the pump to cycle slowly until the system and 

grease is free of air.

If the pump assembly does not prime, refer to the 

Troubleshooting Chart for details.

WARNING

Should leakage occur anywhere within the

system, disconnect air to the motor. Personal
injury can occur.

With air pressure at zero:

  9. Attach a control valve to the outlet hose of the pump.

10. Set the air pressure to 100 psi (6.9 Bar).

11. Operate the control valve into a container.

12. Allow the pump to cycle until the system and grease is 

once again free of air.

13. Shut off the control valve.

• Visually inspect the pump for external leaks.
• The pump should not cycle.

If the pump does not stall, refer to the 

Troubleshooting Chart for details.

14. Check the motor for air leakage.

If the motor leaks, refer to the Air Motor Service 

Guide for details. 

Installation

Additional items that should be incorporated into the 

air piping system are illustrated in Table 5.

* Although the air motor is lubricated at the factory, 

the life of the motor can be extended with the use of a 
lubricator.

Part Number

Description

338860

Moisture Separator/Regulator & Gauge Combination

5604-2

Moisture Separator

7604-B

Regulator and Gauge

5904-2

Lubricator *

Table 5

Air Line Components

Содержание Easy Lube 40-70










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды