Vaisala GroundCast DRS611 Скачать руководство пользователя страница 11

Vaisala GroundCast is designed to function in rough conditions below the ground level. Due to
the waterproof design of the device, the Li-SOCl

2

 batteries are not easily removable.

Therefore, the device shall be recycled as hazardous battery waste in one piece.

Do not attempt to remove the batteries from the device as this

may lead to serious injury or death due to high electrical voltage and/or
energy.

The recycling of batteries must only be conducted by fully trained personnel of
licensed recyclers.

WARNING!

The sensor contains a battery, which poses a fire, explosion, and

severe burn hazard.
Do not crush, disassemble, heat above 100 °C (212 °F), or incinerate.

WARNING!

Recycle the device in accordance with local hazardous waste management practices and
regulations.

Hazardous battery waste

Metal waste

Plastic waste

1

3

4

2

5

# Description

Material

Recycling

1 Vaisala GroundCast

Various, including lithium
thionyl chloride battery

Hazardous battery waste

2 Adjustment block

Aluminum

Metal waste

3 Device holder

Aluminum and stainless steel

Metal waste

4 Dummy block

Polyxymethylene (POM)

Plastic waste

5 Vaisala GroundCast removal

tool

Aluminum, stainless steel, and
red brass (gunmetal)

Metal waste

11

Содержание GroundCast DRS611













Отзывы: