background image

User's Guide ______________________________________________________________________

56 __________________________________________________________________ M210855EN-C

0703-033

Figure 32

Graphical Display

Trend graph

: Displays a curve of average values. Each value is a 

calculated average over a period. 

Max/min graph

: Displays the minimum and maximum values in a 

form of curve. Each value is max/min over a time period. See Table 7 
below.

-

Press the up/down arrow buttons to zoom in and out the time in the 
graph window.

-

Press the left/right arrow buttons to monitor the cursor mode where 
you can observe individual measuring points. Press an arrow 
button to move the cursor (vertical bar) along the time axis. The 
numerical value at the cursor position is shown at the left upper 
corner. Time from the present to the chosen moment is shown at 
the upper right corner.

Table 7

Periods for Trend and Max/Min Calculations

Observation 
Period

Period for Trend/Max/Min Calculations 
(Resolution)

20 minutes

10 seconds

3 hours

90 seconds

1 day

12 minutes

10 days

2 hours

2 months

12 hours

1 year

3 days

Table 8

Graph Information Messages in Cursor Mode

Message

Interpretation

Power outage

Power failure (marked also with dashed 
vertical line)

No data

No data was recorded at pointed time.

Main unit failure

Generic failure detected at pointed time.

Meas. failure

Measurement failure detected at pointed time.

Adj. mode active

The device was in the adjustment mode at 
pointed time.

Содержание BAROCAP PTB330












































































































































Отзывы: