Vaillant VPV P 290/2 M SWF, Инструкции по эксплуатации, установке и обслуживанию

Страница: 6 / 32

6.3 Repair
>
Before carrying out repair work, temporarily decommis-
sion the entire photovoltaic installation (
¬
page 3 ).
>
Replace any defective components.
>
Do not carry out any repairs in the connection box.
>
Start up the photovoltaic installation again (
¬
page 5 ).
7 Inspection and maintenance
>
Follow the inspection and maintenance plan in the
appendix.
>
Temporarily decommission the photovoltaic installation
>
(
¬
page 3 ).
7.1 Checking the insulation and stability of the
cabling
>
Check the cabling, insulation and plug connections for
cleanliness, integrity and stability.
>
Document and eliminate all faults.
7.2 Checking the end and middle clamps
>
Check all of the end and middle clamps on the photovol-
taic modules to ensure that they are correctly connected
to the mounting frame and the PV module frame.
7.3 Checking the protective earthing
>
Check the cabling of the protective earthing for cleanli-
ness, integrity and stability.
7.4 Completing inspection and maintenance
work
>
Document the inspection work that was carried out in an
inspection report.
>
Point out to the end user that they must always keep the
inspection report safe.
>
Start up the photovoltaic installation again (
¬
page 5 ).
8 Decommissioning
8.1 Permanently decommissioning the
photovoltaic installation
>
Observe the instructions for the inverter.
>
Cover the photovoltaic modules with an opaque plastic
film or a fleece in order to minimise the generation of
direct current.
8.2 Removing the photovoltaic module
>
Decommission the photovoltaic installation.
>
Remove the photovoltaic modules and observe the infor-
mation on the electrical installation and set-up.
9 Technical data
VPV P
290/2 M
SWF VPV P
300/2 M
BBF VPV P
305/2 M
BWF
Nominal output P
nom
290 W 300 W 305 W
Voltage at P
max
U
mpp
31,3 V 31,2 V 31,4 V
Current at P
max
I
mpp
9,25 A 9,63 A 9,72 A
Short-circuit current I
sc
9,80 A 9,97 A 10,06 A
No-load voltage V
oc
39,3 V 39,4 V 39,6 V
Dimensions (W x H x D) 990 x 1660
x 35 mm
990 x 1660
x 42 mm
990 x 1660
x 42 mm
Frame height 35 mm 42 mm
Weight
19 kg
Frame material
Al
VPV P
290/2 M
SWF VPV P
300/2 M
BBF VPV P
305/2 M
BWF
Connections Connection box ( 2 , image 2 ) with
three bypass diodes, 4 mm² cable
and MC4 plug connection. Length
per pin: 1200 mm (+) (
4 , image 2 )
and 800 mm (−) ( 3 , image 2 )
Module efficiency 17,6 % 18,3 % 18,6 %
Current coefficient α 0,05
Voltage coefficient β −0,29
Power coefficient γ −0,40 %/K
Maximum permissible sys-
tem voltage U
max
1000 V
DC
Reverse current capacity 20 A
Pressure load (design
load) 5400 Pa 1 7500 Pa 1
Pressure load (dimension-
ing load)
2
3600 Pa
1
5000 Pa
1
Suction load (design load) 2400 Pa
1
Suction load (dimension-
ing load)
2
1600 Pa
1
Mechanical load in accordance with IEC/EN 61215
1 Observe the installation conditions in the installation instructions
2 Design load/safety factor 1.5 = dimensioning load
This module is rated as application class A in accordance
with IEC 61730. The electrical performance data can be
found in the data sheet or on the data plate.
10 Inspection and maintenance work
– Overview
The table below lists the manufacturer requirements with
respect to minimum inspection and maintenance intervals. If
national regulations and directives require shorter inspec-
tion and maintenance intervals, you should observe these
instead of the intervals listed.
No. Maintenance work Interval
1 Checking the end and middle clamps Annually 6
2 Cleaning the photovoltaic module Annually 6
3 Checking the installation site Annually 4
4 Checking the protective earthing Annually 6
5 Checking the inverter Annually -
Installation and maintenance instructions
6
0020273012_00