background image

Manual - Solar hot water systems 0020009607_02

30

Appr

o

x

imat

e c

ylinder he

at up time  15  C t

o

 4

5

  C (

minut

e

s)

R

ehe

at time f

or 7

0

 % o

f c

ylinder c

o

nt

en

ts

 (

minut

e

s)

10

15

20

25

30

20

25

30

35

40

45

12

Heat input to cylinder (kW)

15

20

25

30

38

35

VIH S GB 200 S

VIH S GB 250 S

VIH S GB 300 S

Fig. 5.4 auroSTOR cylinder heat-up times (boiler part)

40

40

8 bar*

4 bar*

3 bar*
2 bar*

1 bar*

30

30

20

20

Flow available (litres/min) at entry to system

Flo

w out (litr

e

s

/m

in

) o

f the s

y

s

tem

10

10

0

Fig. 5.5 auroSTOR hot water flow rates at 60 °C

*  Static operating pressure of the cold water supply

The displayed flow rates apply to installations in which
the cold water supply is of appropriate dynamic 
pressure.
Please contact Vaillant Ltd if the static water pressure is
below 1 bar.

8 bar*
4 bar*
3 bar*

2 bar*

1 bar*

Flow available (litres/min) at entry to system

Flo

w

 out (litr

e

s

/m

in

) o

f the s

y

s

tem

40

40

30

30

20

20

10

10

0

Mixed water of 40 °C, mixed from

 

60 % hot water of 60 °C and

 

40 % cold water of 10 °C

Fig. 5.6 auroSTOR mixed water flow rates

5 Installation

Содержание auroTHERM VFK 900






































































Отзывы: