Vaillant auroTHERM VFK 900 страница 3 Скачать руководство пользователя | Manualshive

Страница: 3 / 69

background image

3

Manual - Solar hot water systems 0020009607_02

1

Notes on the documentation

Your solar system is a quality product from Vaillant.
This manual describes the entire system, all of its
components and the cylinder and provides you with
information on start-up, maintenance and trouble-
shooting. It is a supplement to the operating, installation
and assembly manuals of the individual components.

Observe the manuals for each

individual system

component in conjunction with this manual.

Look after this manual and pass it on to the next owner.

h

Note!

The “Start-up” and “Maintenance and
troubleshooting” chapters of this manual are
intended only for approved specialists.

Vaillant accepts no liability for any damage caused by
failure to observe this manual.

Other applicable documents

-  Assembly manual of the collectors
-  Operating and installation manual of the controller
-  Operating and installation manual of the boiler (if

used)

- Assembly, operating and installation manuals of all

accessories used

- Warranty card

1.1

Storage of documents

Store this manual and all other applicable documents
where they are readily available.
Pass the documents on to the next owner if you move or
sell the unit.

1.2 Symbols

used

Please observe the safety instructions in this manual
when operating and installing the solar system and the
auroSTOR solar cylinder.
The symbols used in the manual are explained
below:

d

Danger!

Immediate risk of serious injury or death!

e

Danger!

Danger of death from electric shock!

e

Danger!

Risk of burns or scalding!

a

Caution!

Potentially dangerous situation for the product
and environment.

h

Note!

Application recommendation.

• Symbol for a required task

1.3

Validity of the manual

This manual is valid exclusively for units with the follo-
wing article numbers:

Appliance type

Cylinder volume

Article number

VIH S GB 200 S

200 litres

307206

VIH S GB 250 S

250 litres

307207

VIH S GB 300 S

300 litres

307208

Table 1.1 Validity of the manual

To find out the article number of your unit refer to the
identification plate.

2

Overview of standards,
safety instructions

2.1

Overview of EU standards

Solar system in general

EN ISO 9488

Thermal solar system and components, terminology
(ISO/DIS 9488; 1995)

EN 12975-1

Thermal solar systems and components; Collectors, Part
1: General requirements

EN 12975-2

Thermal solar systems and components; Collectors; Part
2: Test methods

EN 1991-2-3

Eurocode 1 – Basis of design and actions on structures,
Part 2–3: Actions on structures - Snow loads

EN 12976-1

Thermal solar systems and components;
Factory made systems - Part 1: General requirements

EN 12976-2

Thermal solar systems and components;
Factory made systems - Part 2: Testing methods

ENV 12977-1

Thermal solar systems and components;
Custom built systems,
Part 1: General requirements

Notes on the documentation 1

Overview of standards, safety instructions 2

«
1
2
3
4
5
...
»

Содержание auroTHERM VFK 900






































































Отзывы:

Нет отзывов

Похожие инструкции для auroTHERM VFK 900

Бренд: WINDY NATION Страницы: 21

Бренд: Sutron Страницы: 46

Бренд: Aaeon Страницы: 37

Бренд: Define Instruments Страницы: 28

Бренд: Bongshin Страницы: 45

HPC170SR-ITQ170 Series

Бренд: JETWAY Страницы: 41

Бренд: Solibro Страницы: 22

Бренд: Go Power! Electric Страницы: 16

Бренд: Roofit.Solar Страницы: 25

Бренд: PV-ezRack Страницы: 17

Бренд: Rosemount Страницы: 42

Бренд: Janz Tec Страницы: 40

Бренд: Aaeon Страницы: 97

Бренд: Zennio Страницы: 2

Бренд: Zennio Страницы: 126

Бренд: Quanmax Страницы: 34

Бренд: Waterboy Страницы: 16

AFL2-12A-D525 Series

Бренд: IEI Technology Страницы: 180

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды