9 Handing the product over to the operator
14
Installation and maintenance instructions recoVAIR 0020159949_07
Function
Explanation
Appliance type
You can use this function to set whether
you are installing/have installed a wall
unit or a ceiling unit.
Adjustment options:
–
1 = Small wall unit (air volume flow
260 m
³
/h)
–
2 = Large wall unit (air volume flow
360 m
³
/h)
–
3 = Ceiling unit (air volume flow
150 m
³
/h, L variant)
–
4 = Ceiling unit (air volume flow
150 m
³
/h, R variant)
8.1
System efficiency
8.1.1
Starting the system efficiency monitoring
1.
Call up the installer level. (
→
Page 12)
2.
Navigate to the
Test menu
→
Check programmes
→
Initialisation measure
menu item.
3.
Start the check programme.
◁
If the check programme has been successfully run,
the
System efficiency
function can be selected
from the
Configuration
menu.
4.
Navigate to the
Configuration
→
System efficiency
menu item.
5.
Activate the
System efficiency
function.
6.
Exit the installer level. (
→
Page 12)
8.1.1.1 Checking system efficiency
Conditions
: The
Initialisation measure
check programme has been run
once before
▶
Call up the installer level. (
→
Page 12)
▶
Navigate to the
Test menu
→
Check programmes
→
System efficiency test
menu item.
▶
Start the check programme.
◁
If the check programme has been successfully run,
the degree of system efficiency is shown in the
display.
1 / 2
Test result:
Efficiency: High
Test result:
Efficiency: Medium
Test result:
Efficiency: Low
If the
Efficiency: Low
test result is shown in the display,
first try to increase the system efficiency. (
→
Page 16)
If it is not possible to increase the system efficiency, re-
measure the system. (
→
Page 14)
2 / 2
The check programme was not run successfully.
Establish the system efficiency. (
→
Page 16) If you can-
not establish the system efficiency, re-measure the sys-
tem. (
→
Page 14)
▶
Exit the installer level. (
→
Page 12)
8.1.1.2 Measuring/initialising the system
1.
Call up the installer level. (
→
Page 12)
2.
Navigate to the
Test menu
→
Check programmes
→
Initialisation measure
menu item.
3.
Start the check programme.
◁
The system was measured or initialised again.
◁
The
System efficiency
function is still active.
4.
Exit the installer level. (
→
Page 12)
9
Handing the product over to the
operator
▶
Inform the operator about how to handle the system. An-
swer any questions the operator may have. In particular,
draw attention to the safety information which the oper-
ator must follow.
▶
Inform the operator of the necessity to have the system
maintained according to the specified intervals.
▶
Provide the operator with all relevant instructions and unit
documentation for safe keeping.
▶
Inform the operator that the product must not be operated
together with open-flued combustion locations without a
protection device.
10 Inspection, maintenance and repair
Danger!
Risk of death from live connections
(230 V)!
Risk of death from electric shock when work-
ing on live connections (230 V).
▶
Before carrying out any work on the
product, pull the product's mains plug
out of the earthed plug socket or use the
circuit breaker (depending on the country)
to switch off the product's power supply.
▶
Secure the power supply against being
switched on again.
▶
Check that there is no voltage in the con-
nections.
10.1
Procuring spare parts
The original components of the product were also certified
by the manufacturer as part of the declaration of conformity.
If you use other, non-certified or unauthorised parts during
maintenance or repair work, this may void the conformity of
the product and it will therefore no longer comply with the
applicable standards.
We strongly recommend that you use original spare parts
from the manufacturer as this guarantees fault-free and safe
operation of the product. To receive information about the
available original spare parts, contact the contact address
provided on the reverse of these instructions.
