manualshive.com logo in svg
background image

 

2

1. PREFACE 

1.1 GENERAL 

This manual contains installation, operation and maintenance instructions for Ticket Printers series 
7888 installed to VAF MidFlow

®

 and HiFlow

®

 liquid flowmeters Series ‘J’ . For IOM instructions of the 

flowmeter section refer to Technical Manual 131 or 137 supplied with the instrument. 
Every Ticket Printer is thoroughly tested at the factory before installation on the meter. However, like 
any precision mechanism, it requires periodic care to ensure maximum service. This manual is for use 
in areas where factory rebuilding facilities and adequate exchange stocks are not readily accessible 
This manual contains important information for the installer, the operator and for your maintenance 
department.  
 
To ensure safe and correct installation and operation, study this manual carefully before starting 
operations. 
 
For any additional information contact: 
VAF Instruments B.V.

 

Tel.  

+31 78 618 3100

 

Vierlinghstraat 24, 3316 EL Dordrecht

Fax  

+31 78 617 7068

 

P.O. Box 40, NL-3300 AA Dordrecht

 

E-mail:

[email protected]

 

The Netherlands

 

Internet: 

www.vaf.nl

 

 

Or your local authorized VAF dealer.

 

Their addresses can be found on 

www.vaf.nl

 

 

1.2 COPYRIGHT 

This manual is copyrighted with all rights reserved. 
While every precaution has been taken in the preparation of this manual, no responsibility for errors or 
omissions is assumed. Neither is any liability assumed for damages resulting from the use of the 
information contained herein. Specifications can be changed without notice. 
MidFlow

®

 and HiFlow

®

 are registered trademarks of VAF Instruments B.V. 

 

 

 

Содержание 247

























Отзывы: