Vaderstad Seed Hawk Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 34

background image

Complaint

Troubleshooting Advice

Load cells not reading

accurately

Go into tech app/LC3 and find the bin you are having issues with. Make sure the raw and

filtered weights are even or close to it for all 3 load cells. If one is way off you likely have a failed

load cell. Make sure the voltage on the bottom line reads 24 or 25. Also check to ensure there is

a gap between the stainless primary pipes and meter bottom.

Meter motor not turning

Check operating system for error codes needing to be cleared.

Swap a functioning motor from a different tank with the non functioning one, this will

determine if it is a problem with the PM4 or the motor itself.

No fan RPM

Check gap between the fan speed sensor and the fan plate, it should be 1/16”.

Make sure fan is turning. Switch the sensor plugs and run to see if it is a failed sensor.

No product being discharged

Check to see that bulk shut-offs on each tank are open.

Make suer that each bin is pressurizing the correct air stream (banjo valves on side of tanks)

No power to the entire unit

Ensure your ISO harness is plugged into your tractor correctly (this starts the gateway and

ECUs). If ECUs are blinking then ISO power is working and you will need to check the relay in

the control panel.

No power to gateway

Ensure the toggle switch on the control panel is in the ON position.

Ensure your ISO power cable is plugged into your tractor correctly, check the fuse on the cable

Disconnects

Change wifi channel (at least 2 channels from the current).

Ensure you are running both iPads.

Is it a gateway 100? If so, see service bulletin on troubleshooting and potential upgrade to

Gateway 260.

If it is a gateway 260, check connection points for loose or pushed in pins.

App not loading on iPad

Ensure you are connected to the gateway wifi channel.

Ensure you have the latest version of the app, if not, the old version will not load and you will

need to connect to the internet to install the latest version to your iPad.

«
...
21
22
23
24
25
...
»

Содержание Seed Hawk



































Отзывы:

Нет отзывов

Похожие инструкции для Seed Hawk

Бренд: Supero Страницы: 130

Бренд: Oliver Страницы: 20

drive 4X IC D EX

Бренд: EWM Страницы: 107

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды