VADDIO WallVIEW PRO 300 Скачать руководство пользователя страница 5

WallVIEW PRO 300 

WallVIEW PRO 300 Installation and User Guide 341-668 Rev. B                                                                      Page 5 of 10 

CARE AND CLEANING 

  Do not attempt to take the products in the system apart.  There are no user-serviceable components.  

  Keep the devices away from food and liquid, and do not spill liquids on the products.  

  For smears or smudges on the lens, wipe with a clean, soft cloth.  Do not use any abrasive chemicals on 

the camera body at any time. 

 

OPERATING AND STORAGE CONDITIONS 

Do not store or operate the WallVIEW PRO System under the following conditions: 

  Temperatures above 40°C (104°F) or below 0°C (32°F), for Indoor Use Only 

  High humidity, condensing or wet environments 

 Dusty 

environments 

  In inclement weather 

  Under severe vibration 

 
 

GENERAL SPECIFICATIONS 

Quick-Connect Interface  

Connectors 

Power Connector:  5.5mm OD x 2.5mm ID 
Power RJ-45:  Supplies 36V to EZCamera Interface Module Regulator 
IR:  2-Pin Phoenix type spring cage connector 
Video Outputs:  BNC Connectors for HD Analog Component (Y,PB,PR) or SD 
Video RJ-45:  Transports HD or SD video from camera depending on camera selection switch position 

Camera Select Switch 

8-Position DIP switch loads camera profiles and IR Forwarding for Polycom and TANDBERG Codecs 

Video Adjustments 

Y-Gain (luminance gain) for fine tuning over longer cable distances 
Distance Compensation:  100’, 200’, 300’, 400’+ 

Compatible Cameras 

Sony BRC-H700, BRC-Z700, EVI-HD1, BRC-300, (EVI-D70, EVI-D100 also in SD Mode) 
Polycom EagleEye  

Max. Cat. 5 Cable 
Distance 

Up to 500’ (152.4m) for Video Power and Control 

Power Supply 

36 VDC, 2.78 Amp 

Dimensions 

1-RU Rack Mount (1.75” H x 19” W x 6” D) 

EZCamera Interface Module 

Connectors

 

Four (4) RJ-45 Connectors 
One DB-25 for Power, Video, Control & IR  

Cable Assemblies 

For Sony SD Cameras:  DB-25M to RCA-M/4-Pin Mini Din/8-Pin Mini Din x 2/EIAJ4 Power Connector 

Power Regulator 

Supplies 12VDC to Cameras 

Dimensions 

Approx.  (3.035” H x 4.46” W x 1.242” D) 

 

 

 

 

WallVIEW 300 System 

System Part Numbers 

999-6205-000 NTSC 
999-6205-001 PAL 

Sony BRC-300 Camera 

Camera Part Number 

BRC-300 

Image Sensor 

1/4.7-type CCD 

Effective Pixels 

Approx 1-Mill Pixels (x 3) 

Signal Systems 

NTSC or PAL 

Video Resolutions 

480i  

Lens 

12X Optical, 4X Digital, 48X total 

Horiz. Viewing Angle 

3.3 to 37.8 degrees (4:3); 4.0 to 45.4 degrees (16:9) 

Weight 

Approx. 5 lbs 8 oz (2.5 kg) 

Dimensions 

Approx 7-1/8” W x 8-3/8” H x 8-1/8” D 
(180mm x 210.1mm 205mm)  

Содержание WallVIEW PRO 300











Отзывы: