background image

Installation and User Guide

 

 

Camera and Electronic Products for Integrators

 

 

2004 Vaddio - All Rights Reserved.  Reproduction in whole or in part without written permission is prohibited.  Specifications and 

pricing are subject to change without notice.  CeilingVIEW, WallVIEW ControlVIEW, EZCamera and PowerRite are registered 
trademarks of Vaddio, Inc. All other trademarks are property of their respective owners. Form Number 341- 075 Rev. D 

CeilingVIEW 70 PTZ HideAway 

Installed PTZ Ceiling Camera with Recessed, Motorized Camera Lift System 

 
 
 
 
 
 
 
 
 

Vaddio’s CeilingVIEW 70 PTZ HideAway camera system is 
designed to provide system integrators with an easy to install, 
recessed, in ceiling, motorized camera lift system (see Figure 1).  
The system features a Sony

® 

EVI-D70 PTZ Camera mounted into a 

recessed, metal ceiling camera enclosure with ceiling tile support 
and is equipped with Vaddio’s EZCamera™ Cabling System which 
allows the integrator to use Cat. 5 cabling to run power, video and 
camera control.  The camera lift has a motorized extension arm, 
that 

when retracted, conceals the camera. When the camera is 

activated the extension arm lowers and reveals the camera.  
 

Contact closure or voltage sensing can be used to activate the lift 
system remotely or the camera IR remote control can be used to 
activate the lift with the ON/OFF button.  The VISCA control 
interface is included to allow the camera to work with any other 
VISCA compatible control device. The PowerRite™ power supply 
regulates the right amount of power needed for the camera over the 
Cat. 5 cabling.  

 

 

Before operating the Vaddio CeilingVIEW 70 PTZ HideAway, 
please read the entire manual thoroughly. The camera system was 
designed, built and tested for use indoors with the provided power 
supply. The use of a power supply other than the one provided or 
outdoor operation has not been tested and could damage the 
camera and/or create a potentially unsafe operating condition. 

 

The information contained in this manual will help you install and 
operate your Vaddio CeilingVIEW 70 PTZ HideAway.  If these 
instructions are misplaced, Vaddio keeps copies of Specifications, 
Installation and User Guides and most pertinent product drawings 
for the Vaddio product line on the website.  These documents can 
be downloaded from 

www.vaddio.com

 free of charge.   

 

SAVE THESE 
INSTRUCTIONS 

INTENDED USE 

INTRODUCTION 

Figure 1:  

Vaddio 

CeilingVIEW 70 
PTZ HideAway 
shown retracted 
(left) and lowered 
into operating 
position (right) 

Содержание CeilingVIEW 70 PTZ HideAway















Отзывы: