vacuubrand MV 10C NT VARIO o.C. Скачать руководство пользователя страница 96

Страница: 96 / 152

page 96 of 152

Fault

Possible cause

Remedy

❑

No display.

➨

Electrical power cord

not plugged in, electri-

cal supply failure?

✔

Plug in power cord.

Check fuse.

➨

Device fuse blown?

✔

Identify cause of failure.

Replace device fuse.

➨

Controller CVC 3000

or pump NT VARIO

switched off?

✔

Switch on controller and/

or pump.

➨

VACUU•BUS cable

between pump and

controller not plugged

in at controller?

✔

Plug in VACUU•BUS

cable at CVC 3000 con-

troller.

➨

Other than above men-

tioned causes?

✔

Contact local distributor.

❑

Display disappears.

➨

Too much load (e.g.,

valves) connected?

✔

Check current draw of the

connected devices.

➨

Short circuit at connect-

ed valves?

✔

Replace valves.

➨

Short circuit at the

RS 232 plug?

✔

Check plug and cable.

➨

Other than above men-

tioned causes?

✔

Contact local distributor.

❑

Pressure reading

incorrect.

➨

Pressure transducer

decalibrated?

✔

Readjust CVC 3000.

➨

Humidity in the mea-

surement chamber?

✔

Let the pressure trans

ducer dry, e.g., by pump-

ing. Readjust if neces-

sary. Determine and

eliminate the cause for

humidity.

➨

Pressure transducer

contaminated?

✔

See ”Cleaning the pres-

sure transducer”.

➨

Other than above men-

tioned causes?

✔

Contact local distributor.

❑

Digital pressure

reading is flash

ing, display shows

”0.0”.

➨

Pressure transducer

not correctly adjusted

under vacuum?

✔

Adjust CVC 3000 cor-

rectly.

Troubleshooting

Содержание MV 10C NT VARIO o.C.

























































































































































Результаты поиска

Содержание MV 10C NT VARIO o.C.

Отзывы:

Похожие инструкции для MV 10C NT VARIO o.C.

Бренды по названию

Популярные бренды

vacuubrand MV 10C NT VARIO o.C., Инструкция по эксплуатации

Результаты поиска

Содержание MV 10C NT VARIO o.C.

Отзывы:

Похожие инструкции для MV 10C NT VARIO o.C.

Бренды по названию

Популярные бренды