Vacon 50X Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 132

background image

47

vacon

keypad operation and programming

Tel. +358 (0)201 2121 • Fax +358 (0)201 212205

5

9.

If the test was successful, the drive will stop and return to the configured control
path. The “Motor RS” parameter will contain a new value that is the calculated re-
sistance of the motor.

10.

If the test was not successful, the drive will fault with a “RS Meas. Fail” message
(Fault 34). If the test fails, you may want to try the test again with a different “Rated
Mtr FLA” or different Current Limit percentage.

11.

If the measurement process fails for any reason, it is possible to physically measure
motor resistance by using an ohmmeter and dividing the result by 2. Then enter this
value manually into parameter 514 (Motor RS).

5.6.2 Activating Automatic RS Measurement via Serial Link (Modbus)

1.

Make sure there is no load applied to the motor and that the motor shaft is free to

spin without damage or injury.

2.

Configure the following parameters to the data provided on the nameplate of the
motor:

•

Rated Mtr Volt (509)

•

Rated Mtr FLA (510)

•

Rated Mtr RPM (511)

•

Power Factor (515)

3.

Change parameter “Find Mtr Data” (519) to a value of “Motor RS.” At this point, the
RS Measurement will be armed.

4.

Start the RS Measurement by writing a value of 0x0007 to parameter “SIO Cntl
Word” (904).

5.

The measurement begins as the drive injects voltage to the motor at zero frequency.
The test lasts about two seconds.

6.

If the test was successful, the drive will stop and return to the configured control
path. The “Motor RS” parameter will contain a new value that is the calculated re-
sistance of the motor.

7.

If the test was not successful, the drive will fault with a “RS Meas. Fail” message
(Fault 34). If the test fails, you may want to try the test again with a different “Rated
Mtr FLA” or different Current Limit percentage.

8.

If the measurement process fails for any reason, it is possible to physically measure
motor resistance by using an ohmmeter and dividing the result by 2. Then enter this
value manually into parameter 514 (Motor RS).

«
...
46
47
48
49
50
...
»

Содержание 50X





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 50X

Бренд: Badger Basket Страницы: 3

Бренд: Haier Страницы: 58

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: Ultrak Страницы: 41

Бренд: Zander Aachen Страницы: 10

medialon Showmaster Go

Бренд: 7th Sense Страницы: 2

Бренд: Eaton Страницы: 6

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 4

GAT ACCESS 6100

Бренд: Gantner Страницы: 4

Бренд: halstrup-walcher Страницы: 39

Бренд: xpr Страницы: 4

Smart Control Panel 880RGD

Бренд: Raynor Страницы: 4

Бренд: cinetto Страницы: 56

Cutler-Hammer Jockey

Бренд: Eaton Страницы: 12

Бренд: HW Group Страницы: 18

Бренд: EFI Страницы: 127

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды