Vacon 100 HVAC Скачать руководство пользователя

Страница: 157 / 201

NOTE!

For a stall state to occur, the output frequency must be below this limit for a

certain time.

10.9.3

UNDERLOAD (DRY PUMP) PROTECTION

The motor underload protection makes sure that there is a load on the motor when the drive

operates. If the motor loses the load, a problem can occur in the process. For example, a belt

can break or a pump become dry.

You can adjust the motor underload protection with parameters P3.9.16 (Underload

Protection: Field Weakening Area Load) and P3.9.17 (Underload Protection: Zero Frequency

Load). The underload curve is a squared curve between the zero frequency and the field

weakening point. The protection is not active below 5 Hz. The underload time counter does

not operate below 5 Hz.

The values of the underload protection parameters are set in percentage of the nominal

torque of the motor. To find the scaling ratio for the internal torque value, use the data in the

name plate data of the motor, the motor nominal current and the nominal current of the

drive I

. If you use another current than the nominal motor current, the precision of the

calculation decreases.

NOTE!

If you use long motor cables (max. 100 m) with small drives (≤1.5 kW), the motor

current that the drive measures can be much higher than the actual motor current.

It is because there are capacitive currents in the motor cable.

P3.9.15 UNDERLOAD FAULT (ID 713)

Use this parameter to select the response of the drive to an 'Underload' fault.

If the underload protection function detects that there is not a sufficient load on the motor,

an underload fault occurs.

P3.9.16 UNDERLOAD PROTECTION: FIELD WEAKENING AREA LOAD (ID 714)

Use this parameter to set the minimum torque that the motor needs when the output

frequency of the drive is higher than the frequency of the weakening point.

You can set the value of this parameter between 10.0 and 150.0% x T

nMotor

. This value is the

limit for the minimum torque when the output frequency is above the field weakening point.

If you change parameter P3.1.1.4 (Motor Nominal Current), this parameter goes

automatically back to its default value. See Chapter 5.9 Group 3.9: Protections.

PARAMETER DESCRIPTIONS

VACON · 157

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды