Vac-U-Boat Vac-U-Soling Lower Hull Kit Скачать руководство пользователя страница 22

Страница: 22 / 30

Turn over the deck. Now those four magnets are sanded-side-up and located right on top of the other magnets. You have

already sanded the inside corners of the Cockpit Cover. Put a droplet of CA (Super Glue) on the center of each magnet.

Install the Cockpit Cover onto the Cockpit opening and press in place. Turn both over to make sure the Cover made contact

with the Magnet and the CA is visible (arrow). If one is not touching, press on both side until they are touching and hold for

20 seconds for the CA to bond. Remove the Cockpit Cover. The CA is temporary. It will come loose in time. For a

permanent bond take some filled epoxy and work it around the Magnet’s sides. Clean away epoxy between the magnet and

the corner of the Cockpit Cover (arrow). This leaves room for the raised edge of the Cockpit opening.

The Hull is ready for the Deck. Leave the Hull on the Keel to cure overnight, approximately 24 hours and seal the end of the

caulking tube to keep fresh until then.

Two more things to do to the Deck before tomorrow.

The magnets you glued to

the underside of the Deck were sanded-side-down. You clamped that magnet in place by putting another magnet under it.

Apply a thin bead of sealant to the side flanges of the Battery Tray and press into the hull. Wipe away any excess sealant.

Содержание Vac-U-Soling Lower Hull Kit































Результаты поиска

Содержание Vac-U-Soling Lower Hull Kit

Отзывы:

Похожие инструкции для Vac-U-Soling Lower Hull Kit

Бренды по названию

Популярные бренды

Vac-U-Boat Vac-U-Soling Lower Hull Kit, Инструкция по эксплуатации

Результаты поиска

Содержание Vac-U-Soling Lower Hull Kit

Отзывы:

Похожие инструкции для Vac-U-Soling Lower Hull Kit

Бренды по названию

Популярные бренды