E
N
G
L
IS
H
PROGRAMMING OF THE TIMER FUNCTION
To memorize the TIMER function on the first channel, proceed as
follows:
1.
Press and keep pressed the SW1 button of the receiver :
the led L1 (relating to the first channel) lights up for a few
seconds.
2.
When the led goes off, release the SW1 button. Led L1 starts
flashing slowly (1 flash per second). The number of flashing
corresponds to the time which can be set as shown in the
table.
3.
Count the number of led L1 flashings corresponding to the
time you wish to set.
4.
Press the rx button SW1 during the wished flashing:
the sequence of flashings stops and led L1 remains on.
5.
Press and keep pressed the tx button (it is necessary to
proceed within 5 seconds): if the rx led L1 goes off , it means
the transmitted code has been correctly memorized.
To memorise the channel 2 TIMER function, proceed as follows:
6.
Press and release the SW1 key: LED L1 lights up
7.
Press and hold the SW1 key: LED L2 comes on for a few
seconds
8.
Repeat steps 2,3,4,5 described above, keeping LED L2 as a
reference.
PROGRAMMING OF THE BISTABLE FUNCTION
To memorize the bistable function on the first channel, proceed
as follows:
1.
Press and keep pressed the rx SW1 button : led L1 (relating to
the first channel) lights up for a few seconds.
2.
When led L1 goes off, release SW1 button. Led L1 starts
flashing at low speed ( 1 flash per second).
3.
When the 30 flashings of the timer function are over, led L1
remains on.
4.
Press and keep pressed the tx button: if led L1 goes off it
means the transmitted code has been memorized in the
correct way.
To memorise the channel 2 BISTABLE function, proceed as
follows:
5.
Press and release the SW1 key: LED L1 lights up
6.
Press and hold the SW1 key: LED L2 comes on for a few
seconds
7.
Repeat steps 2,3,4 described above, keeping LED L2 as a
reference
CODE REPLACEMENT
(RXS2KB220 - RXS2KB120 only)
The memorized transmitter code can be replaced by a new code
by following the same procedure for the memorization. In this
way the new code will be memorized and the previous one
cancelled.
ROLLING CODE MODE
(RXP2S220 - RXP2S120 only)
It is possible to activate or disable the ROLLING CODE mode.
Its activation makes any attempt of code duplication impossible.
To activate the "rolling code" function it is necessary to act on
the jumper J1 on the printed circuit:
J1 open
=
"rolling code" mode activated
J1 closed
=
"rolling code" mode not activated
ATTENTION: only when the "rolling code" mode is
activated is the Personal Pass code not reproducible by
someone else.
TOTAL CLEARING
(RXP2S220 - RXP2S120 only)
It is necessary to follow these directions:
•
Disconnect the power supply.
•
Press the receiver's SW1 button; at the same time supply
power.
•
The receiver's LED flashes: release SW1
•
The 83 memory zones are now empty and ready for a new
programming.
ALTERING THE FUNCTION OF AN ALREADY
MEMORISED CODE
(RXP2S220 - RXP2S120 only)
Tring to insert a code already memorized, the old code will be
overwritten by the new one.
Example: if a code was memorized in monostable mode and you
want to memorized it in bistable mode you just have to repeate
the appropriate procedure.
N° Flashing
Time
1
01 sec.
2
02 sec.
3
03 sec.
4
04 sec.
5
05 sec.
6
06 sec.
7
07 sec.
8
08 sec.
9
09 sec.
10
10 sec.
11
11 sec.
12
12 sec.
13
13 sec.
14
14 sec.
15
15 sec.
16
30 sec.
N° Flashing
Time
17
1 min.
18
1,5 min.
19
2 min.
20
2,5 min.
21
3 min.
22
3,5 min.
23
4 min.
24
4,5 min.
25
5 min.
26
5,5 min.
27
6 min.
28
6,5 min.
29
7 min.
30
7,5 min.
31
BISTABLE
Содержание RXP2S220
Страница 16: ......
