Uwatec A700 Скачать руководство пользователя страница 12

Страница: 12 / 13

A700 Step-by-step maintenance procedures.

30. Check for previous

folds/creases on the

diaphragm

“

lip

”.

Any imperfections found

merits replacement.

36. Align the cover (with

screws and o-rings

already installed).

31. Be certain the entire

circumference of the

diaphragm is laying flat

and into the case

diaphragm groove.

37. Begin to lightly snug

the 4 TORX® screws

down, using an X

tightening pattern.

32. With the outside ring

tab @ the

6 o‟clock

position, press the cover

into place, orienting the

bottom of the “S” logo

towards the tab.

38. Using Torque driver,

tighten the screw to the

recommended 6.2 inch

pounds / 0.7 Newton

meters. See tool list on

page 2 of this manual.

33. Place the two piece

assembly, orienting the

ring tab into case notch

located at the “6 o

-clock

position”.

34. Align one cover hole

with an o-ring.

A neoprene surface is

best!

35. Press the screws, one

by one, through the front

cover hole and through

the new 363 o-rings.

The neoprene provides
just enough support and

give, to allow the screw

to pass through the o-ring

until installed.

Neoprene

Содержание A700














Результаты поиска

Содержание A700

Отзывы:

Похожие инструкции для A700

Бренды по названию

Популярные бренды

Uwatec A700, Руководство по обслуживанию

Результаты поиска

Содержание A700

Отзывы:

Похожие инструкции для A700

Бренды по названию

Популярные бренды