e. TO CHANGE THE EVENTS, using the “SET” button,
locate the event setting(s) to change and then use
the instructions in Step 3d through 3m to change the
setting.
f. TO DELETE THE EVENTS, using the “SET” button,
locate either the hour “ON” or hour “OFF” setting to
delete and then use the “-“ and “+” buttons to cycle
through until the clock clears and shows “- : - -”.
NOTE: The clock clears and shows “- : - -” between
the hours of 11 PM and 12 AM.
g. To end Reviewing, Changing & Deleting of Events,
press the “ON/OFF” button and any changes will be
automatically saved or wait about 10 seconds and
changes will be automatically saved.
5. RESET Sequence
a. Press the “RESET” button for 5 seconds with the tip
of a small non-metallic insulated tool, such as a
pencil (not included). Display will flash 12:00 AM.
b. Setup timer by following “Time Setup” in Step 2 of
the instructions or Event Setup” in Step 3.
1. Manual ON/OFF OVERRIDE
Press the “ON/OFF” button to
bypass the current settings and
temporarily turn your attached
devices ON or OFF.
Programmed settings will
resume based on the next
programmed cycle.
HELPFUL TIPS
• To automatically advance through the Hour and Minute
selections, press and hold the “-“ or “+” buttons.
• The “ON/OFF” button can be used as an ENTER key
when setting the Current Time or an ON/OFF Event.
When pressed at any time during setup, it will save the
current entry and return to the main screen.
• The battery icon illuminates and flashes when the
timer is operating on battery power. Restore power to
the timer to preserve all programming.
IN CASE OF POWER FAILURE
Timer will continue to operate on battery backup if the
power goes out; however, it will not turn attached devices
on or off. Once power is restored, programming will
resume. If power remains out longer than the battery
backup will operate, re-program the timer as explained in
Steps 1, 2 and 3 of the “Programming Instructions”.
NOTE: Battery is permanently installed and not
replaceable. It automatically recharges when power is
provided to the timer.
WARNING
Risk of Electric Shock
Keep children away. Unplug timer before cleaning.
Fully insert plug. Do not use in wet locations.
Risk of Fire
Do not use to control appliances that contain heating
elements (cooking appliances, heaters, irons, etc.).
Do not exceed electrical ratings. For Indoor Use Only.
OPERATING MODES
LIMITED 1 YEAR WARRANTY
Prime warrants this product to be free from manufacturing
defects for a period of one year from the original date of
purchase (“warranty period”). This warranty is limited to the
repair or replacement of this product only and Prime is not
liable for any consequential or incidental damage to other
products that may be used with this unit. This warranty is
effective only if such unit is returned to Prime not later than
thirty (30) days after the expiration of the warranty period.
Warranty is void if damage is due to neglect, misuse,
alteration, modification, improper installation, or repair by
other than Prime. This warranty is in lieu of all other
warranties express or implied. Some states do not allow
limitations on how long an implied warranty lasts or permit
the exclusion or limitation of incidental or consequential
damages, so the above limitations may not apply to you.
It is our experience that a product that fails prematurely due
to a manufacturing defect in materials or workmanship, will
generally do so very early in the product’s life cycle, often the
first or second time the product is used. Products that are
returned for warranty inspection after months or years of
continuous reliable service are usually the result of normal
wear and tear, which is not considered a defect in materials
or workmanship and therefore is not covered by the
warranty.
This warranty gives you specific rights, and you may also
have other rights which vary from state to state. If unit should
prove defective within the warranty period, return within the
time period set forth above prepaid with the original
purchase receipt to:
Prime Wire & Cable, Inc.
ATTN: Timer Warranty
280 Machlin Court
City of Industry, CA 91789
SAFETY INFORMATION & SPECIFICATIONS
This timer is a “polarized” device. One blade
on the male plug is wider than the other and is
only intended for use with a polarized outlet.
Use with a three-pronged grounded outlet is
also acceptable.
DO NOT ATTACH A DEVICE THAT EXCEEDS THE UNIT RATINGS:
125 V AC / 60 Hz
15 A / 1,875 W Resistive
(General Purpose)
8 A / 1,000 W Tungsten
(Incandescent)
1/2 HP
(Horsepower Motor)
DAY
On
Off
+
-
Random
+/- 1hr
untdown
R
12
:
00
00
16
OFF
ON
SET
IME
SET
PROG
AM PM
R
MO TU WE TH FR SA SU
COUNTDOWN
2. One-Touch “RANDOM”
Security Setting
Locate the Random icon
underneath the minus (-) and
plus (+) buttons. Press the “-”
and “+” buttons at the same
time to enter or exit the Random
Security Setting. When this
setting is activated, the icon “ ” will appear.
NOTE: This function requires at least one event to be
set up as described in Step 3 of the instructions. The
event must be set for a minimum of 2hrs., 10min.
Timer will randomly turn devices ON/OFF MULTIPLE
TIMES throughout the programmed ON settings.
R
R
SET
DAY
On
Of
+
-
et
Random
+/- 1hr
Countdown
R
12
:
00
00
16
OFF
ON
SET
TIME
SET
PROG
AM PM
R
MO TU WE TH FR SA SU
COUNTDOWN
AVERTISSEMENT
Risque de choc électrique
Gardez les enfants à l’écart. Débranchez la minuterie
avant de procéder au nettoyage. Insérez complètement la
fiche. N’utilisez pas l’article dans des endroits humides.
Risque d’incendie
N’utilisez pas cet article pour commander des appareils
qui contiennent des éléments chauffants (appareils de
cuisson, radiateurs, fers, etc.). Ne dépassez pas les
capacités électriques. Pour usage à l’intérieur seulement.
Printed in China
N
Lights do
not turn on,
even when
timer is in
“Always On”
position.
Lights do
not turn on
and off at
programmed
times.
Lights are not in
“ON” position.
Lights are not
functioning or
timer is not
receiving power.
Timer is not set
properly.
Be sure lights are
functional by plugging
them directly into the
outlet. Be sure that the
lights are in the “ON”
position if they have
their own switch. Be
sure the outlet the
timer is plugged into is
active.
Reset the timer
according to Step 5 of
this manual. Make
sure the “Bypass
Switch” is in the
“Timer On” position.
TROUBLESHOOTING
PROBLEM POSSIBLE
CAUSE
CORRECTIVE
ACTION
AD
FCC REGULATORY STATEMENT
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired operation.
Notes: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and
receiver.
3. Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician
for help.
IC REGULATORY STATEMENT
Under Industry Canada regulations, this radio transmitter
may only operate using an antenna of a type and maximum
(or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other
users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is not
more than that necessary for successful communication.
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
