Utilimaster Aeromaster страница 8 Скачать руководство пользователя

Страница: 8 / 11

8 of 11

03103436-A10015 Rev. C

July 16, 2021

Pedestal Seat Replacement

Seat Removal

1. Remove and retain the (4) nuts and washers attaching the seat to the pedestal.
2.

Pull the seat off the pedestal.

Seat Installation

1. Set the replacement seat in place.

Do NOT use locknuts to hold the seat

to the pedestal.

2. Fasten the (4) nuts and washers.
3.

Torque nuts to 10‑12 ft•lb.

Pedestal Replacement

Pedestal Removal

1. Remove and discard the (4) bolts and nuts

attaching the pedestal to the cab floor.

2. Remove the one bolt attaching the seat belt to the

pedestal.

3. Pull out the pedestal seat.

Pedestal Installation

1. Reverse the removal procedure.

Replace fasteners with

new

Grade 8 fasteners.

Torque to 75‑95 ft•lb.

LCK WASHER

5/16 NUT

PEDESTAL

WASHER

SEAT STUD

LCK WASHER

5/16 NUT

PEDESTAL

WASHER

SEAT STUD

Seat to pedestal fasteners

Seat pedestal attached to floor base

1/2" BOLT

NUT

PEDESTAL

1/2" BOLT

NUT

PEDESTAL

Содержание Aeromaster












Результаты поиска

Содержание Aeromaster

Отзывы:

Похожие инструкции для Aeromaster

Бренды по названию

Популярные бренды

Utilimaster Aeromaster, Руководство по обслуживанию

Результаты поиска

Содержание Aeromaster

Отзывы:

Похожие инструкции для Aeromaster

Бренды по названию

Популярные бренды