UTICA BOILERS MGC 3 Series Скачать руководство пользователя страница 22

Страница: 22 / 36

12 - LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above.
2. Set the thermostat to lowest setting.

3. Turn off all electric power to the appliance.

4. This appliance is equipped with an ignition device which

automatically lights the pilot. Do not try to light the pilot

by hand.

OFF

INLET

GAS CONTROL KNOB

PILOT ADJUSTMENT

(UNDER CAP SCREW)

PILOT
OUTLET

OUTLET

WIRING
TERMINALS (2)

INLET

PRESSURE

TAP

TERMINALS
(2)

GROUND

PRESSURE
TAP

PRESSURE REGULATOR ADJUSTMENT
(UNDER CAP SCREW)

OUTLET

5. Remove lower front panel.
6. Rotate the gas control knob clockwise

to “OFF”.

7. Wait five (5) minutes to clear out any gas. Then

smell for gas, including near the floor. If you smell

gas, STOP! Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s instructions.

If you don’t smell gas, go to next step.

8. Rotate gas control knob counterclockwise

“ON”.

9. Replace lower front panel.
10. Turn on all electric power to the appliance.
11. Set thermostat to desired setting.
12. If the appliance will not operate, follow the instructions

“To Turn Off Gas To Appliance” and call your service

technician or gas supplier.

TO TURN OFF GAS TO APPLIANCE
1. Set the thermostat to lowest setting.

2. Turn off all electric power to the appliance if service is

to be performed.

3. Push in gas control knob slightly and turn clockwise

to “OFF” Do not force.

WARNING

If you do not follow these instructions

exactly, a fire or explosion may result

causing property damage, personal injury

or loss of life.

• This appliance is equipped with an ignition device

which automatically lights burner. Do NOT try to

light this burner by hand.

• Before operating smell all around appliance area

for gas. Be sure to smell next to floor because

some gas is heavier than air and will settle to the

floor.

•

Use only your hand to turn the gas shutoff

valve. Never use tools. If valve will not turn

by hand, do not try to repair it, call a qualified

service technician. Force or attempted repair may

result in fire or explosion.

•

Do not use this appliance if any part has

been under water.

Immediately call a qualified

service technician to inspect appliance and to

replace any part of control system and any gas

control which has been under water.

LIGHTING PROCEDURE FOR BOILER WITH

INTERMITTENT PILOT SYSTEM

For Your Safety, Read Before Operating!!

A. This appliance is equipped with an ignition device

which automatically lights the pilot. Do not try to light

appliance by hand.

CAUTION

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switches; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

•

If you cannot reach your gas supplier, call the fire

department.

Figure 13 - Automatic Gas Valve

PN 240013087 Rev. A [09/30/2020]

Содержание MGC 3 Series





































Результаты поиска

Содержание MGC 3 Series

Отзывы:

Похожие инструкции для MGC 3 Series

Бренды по названию

Популярные бренды

UTICA BOILERS MGC 3 Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание MGC 3 Series

Отзывы:

Похожие инструкции для MGC 3 Series

Бренды по названию

Популярные бренды