USSC Clayton 1600 Скачать руководство пользователя

Страница: 29 / 32

OF EITHER SIDE AT THIS POINT.

4. Attach filter holders to sides of enclosure with sheet metal

screws.

5. Position filter filler

between side filter
holders and secure
to back of furnace
with two self-tapping
screws.

6. Attach blower access

cover to enclosure with
sheet metal screws.

Insert filter (not supplied).

7. Attach handle to filter

cover and slide into
position.

8. Connect cold air return

duct to top flange of

filter box.

NOTE: Drill, punch, or
cut access holes as
necessary for entrance
of power cables,
thermostat wire and
domestic hot water coil

DELUXE FILTER BOX

Model 1600 / 1800 (see service bulletin #2)

16" x 20" x 1" Filter Required

1. Attach sides

of filter box to
bottom with
(4) sheet metal
screws per
side.

Be sure sides
are inside
bottom lips
and positioned
with predrilled
holes as
illustrated.

Side with no

lip

faces

back of
furnace.

2. Position top so 2" wide lip is

turned toward furnace. Place
top over sides and secure
with (4) sheet metal screws
per side.

3. Center assembly from left to right on back of furnace with

bottom of filter box resting on edge of furnace bottom.

Be sure filter
box is perfectly
square. Mark
position of screw
holes on back of
furnace. Drill
starter holes and
secure assembly
to back of furnace
with self-tapping
screws.

NOTE: DO NOT PLACE A SCREW IN THE MIDDLE HOLE

2" Lip

16" x 20" opening

KIT #C61999

Содержание Clayton 1600

































Результаты поиска

Содержание Clayton 1600

Отзывы:

Похожие инструкции для Clayton 1600

Бренды по названию

Популярные бренды

USSC Clayton 1600, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Clayton 1600

Отзывы:

Похожие инструкции для Clayton 1600

Бренды по названию

Популярные бренды