background image

furnace, a gas water heater, or gas furnace. The fumes could
then be distributed throughout the house.

COMBUSTION AIR

All fires need air (specifically oxygen) to burn. Furnaces,
fireplaces, and wood-burning furnaces need enough oxygen
for complete combustion of their fuels. The incomplete
combustion that takes place when a furnace is "air starved"
causes carbon monoxide (CO) to be formed in quantities that
can be dangerous inside a well-sealed house. Having a
source of combustion air from outside prevents this "air
starvation" of the furnace.

Your furnace is shipped from the factory in four (4) packages.
1) the furnace,  2) the blower,  3) draft kit, 4) fan limit kit or
electronic circuit board . Before assembling the furnace, check

ately. He will take the necessary steps to correct the problem.

       Parts List

      All models include the following:

      Two Door Handles

      One Fuel Door Latch

      One Ash Door Latch

      One Shaker Grate Handle

      Two 1/2" Washers

      Four 1/4" Hex Nuts

      Four Lock Washers

      Spin Draft

      Five 1/4" Lock Nuts

      One Pivot Bracket

      Four Brass Coil Knobs

      One 1/4" x 1" Hex Bolt

Two Smoke Door Clips

Rod Extension

Manual

      Three 1/2" Lock Nuts

      One 1/2" x 2 1/2" Carriage Bolt

Six 1/4" x 3/4" Hex Bolts

Smoke Door

Two 1/4" x 1-1/4" Carriage Bolts

ASSEMBLY INSTRUCTIONS

FUEL DOOR
ILLUSTRATION

ASH DOOR
ILLUSTRATION

LOCK

WASHER

HEX

NUTS

     5

to make sure there is no
shipping damage, and that
all necessary parts are
located in the firebox. See
parts list below.

If you find shipping damage
or any of the parts missing,
contact the dealer immedi-

MODEL 1600 - (6) BRICKS ON EACH SIDE

FIREBOX LEFT SIDE

MODEL 1800 - (8) BRICKS ON EACH SIDE

BRICK RETAINING STRIP

FIREBOX LEFT SIDE

BRICK RETAINING STRIP

SLIDE 4th BRICK BACK
BEFORE INSTALLING 5th
AND 6th BRICK

Содержание Clayton 1600

































Отзывы: