US Water Systems Ultimate Dual Superfilter FSF-250 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 31

background image

14

Visit us online at www.USWaterSystems.com Give us a call at: 1-800-608-8792

Filter Preparation

22) Install a threaded adaptor in the secondary tank adaptor lower port. Install the red clip to
secure the threaded adaptor in the secondary tank adaptor. Attach the bottom stainless
steel tube from the primary tank adaptor to the secondary tank adaptor. Tighten the tube to
the threaded adaptor using channel locks.

23) Install a threaded adaptor in the primary tank adaptor top port. Install the red clip to se-
cure it. Now tighten the long stainless steel tube on the threaded adaptor and tighten it with
channel locks.

«
...
12
13
14
15
16
...
»

Содержание Ultimate Dual Superfilter FSF-250
































Отзывы:

Нет отзывов

Похожие инструкции для Ultimate Dual Superfilter FSF-250

Бренд: A.O. Smith Страницы: 2

Бренд: NCR Страницы: 142

Бренд: Radiant Страницы: 8

MiniTank WM-2.5

Бренд: Waiwela Страницы: 20

Бренд: A.O. Smith Страницы: 44

MAG HK 13-2/0-3 H

Бренд: Vaillant Страницы: 12

Бренд: Hamilton Beach Страницы: 14

Бренд: Rinnai Страницы: 2

Бренд: GE Страницы: 20

cIAPMO-T RV-550

Бренд: PrecisionTemp Страницы: 8

arctic compact 12-20 ul

Бренд: Ugolini Страницы: 20

Aquacube COMP827

Бренд: COMPANION Страницы: 12

Indulge Modern F-HC3300

Бренд: InSinkErator Страницы: 1

Paradise Paper Slim

Бренд: CWS Страницы: 2

Бренд: Bobrick Страницы: 4

Бренд: ALPATEC Страницы: 16

VITOWELL EASY P1

Бренд: Viessmann Страницы: 16

Бренд: Queen Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды