US Water Systems Fusion Скачать руководство пользователя страница 29

Страница: 29 / 34

DIAGNOSTIC PROGRAMMING MODE

Diagnostic Programming Mode Options

Abbreviation

Parameter

Description

Flow Rate

Displays the current outlet flow rate

Peak Flow

Rate

Displays the highest flow

rate measured since the last

regeneration

Hours in

Service

Displays the total hours that the

unit has been in service

Volume Used

Displays the total volume of water

treated by the unit

Reserve

Capacity

Displays t

he system’s reserve

capacity calculated from the system

capacity, feedwater hardness, and

safety factor

Software

Version

Displays the software version

installed on the controller

NOTE: Some items may not be shown depending on timer configuration. The timer will exit Diagnostic Mode after 60

seconds if no buttons are pressed. Press the Extra Cycle button to exit Diagnostic Mode at any time.

Diagnostic Programming Mode Steps

1. Press the Up and Extra Cycle buttons for five seconds while in service.

2. Use thi

s display to view the current Flow Rate. This option setting is identified by “FR” in the upper left hand corner of the

screen.

3. Press the Up button. Use this display to view the Peak Flow Rate since the last regeneration cycle. This option setting is

ide

ntified by “PF” in the upper left hand corner of the screen.

4. Press the Up button. Use this display to view the Hours in Service since the last regeneration cycle. This option setting is

identified by “HR” in the upper left hand corner of the screen.

5. Press the Up button. Use this display to view the Volume Used since the last regeneration cycle. This option setting is

identified by “VU” in the upper left hand corner of the screen.

6. Press the Up button. Use this display to view the Reserve Capacity. Thi

s option setting is identified by “RC” in the upper

left hand corner of the screen.

Содержание Fusion



































Результаты поиска

Содержание Fusion

Отзывы:

Похожие инструкции для Fusion

Бренды по названию

Популярные бренды

US Water Systems Fusion, Руководство по обслуживанию

Результаты поиска

Содержание Fusion

Отзывы:

Похожие инструкции для Fusion

Бренды по названию

Популярные бренды