background image

E N G L I S H

19

The Meter is powered by a single 
9V battery (NEDA Type 1604, 6 LF 
22 or 006 p).  To guarantee proper 
functioning of the meter, the 
specified battery alkaline or other 
long-life batteries are recommended.
If the low-battery indicator is shown 
in the display, replace the battery by 
using the following procedur.

 WARNING:

 TO PREVENT ELECTRICAL 

HAZARD OR SHOCK, TURN THE METER 
OFF AND DISCONNECT TEST LEADS 
BEFORE REMOVING THE BACK COVER.

1. Unclamp the Meter from any 
conductor, and turn it off by pressing 
the ON-OFF pushbutton.
2. Place the Meter face down on a 
non-abrasive surface and completely 
loosen the three rear panel screws 
with a Phillipshead screwdriver.
3. Grasp the bottom of the rear cover 
and lift it free of the case.
4. Lift the battery from the case, 
and carefully disconnect the battery 
connector leads.
5. Snap the battery connector leads 
to the terminals of a new battery 
and reinstall the battery cover. Then 
insert the battery into position. Dress 
the battery leads so that they will not 
be pinched between the case bottom 
and the case top. Do not discard 
battery cover.
6. Replace the rear cover, ensuring it 
slips beneath the hold-down lip (next 
to the jaws) and fits securely into 
position.
7. Reinstall the three securing screws. 
If the Meter will not be used for 
periods of longer than 60 days, 
remove the battery and store it 
separately.

5.2 Maintenance

Repairs or servicing should be 
performed by qualified personnel 
only.

 WARNING: 

TO AVOID ELECTRICAL 

SHOCK OR DAMAGE TO THE METER, 
DO NOT GET WATER INSIDE THE CASE. 
REMOVE THE TEST LEADS AND ANY 
INPUT SIGNALS BEFORE OPENING THE 
CASE.

Periodically wipe the case with a 
damp cloth and detergent; do not use 
abrasives or solvents.

5.3 Calibration

The Meter should be calibrated 
annually. Regarding the service /
calibration information on the Meter, 
contact the nearest distributor of the 
Meter.

6. THREE - PHASE POWER 

MEASUREMENTS

Refer to the following figures for 
suggested ways to measure total 
power in a three-phase system. 

Measurement Connections
(3ø, 3 wire)

Содержание UD370

























Отзывы: