Urrea SS950 Скачать руководство пользователя страница 13

13

E N G L I S H •

User’s manual

Cutting oil will keep the blade cool, increase 
cutting action, and prolong blade life.

 WARNING: Never use gasoline, because nor- 

mal sparking could ignite the fumes.
1. Securely clamp the workpiece in position, 
and make the cut close to the clamping point 
in order to minimize vibration of the work be-
ing cut.
2. When cutting conduit pipe or angle iron, 
clamp the work in a vise, if possible, and cut 
close to the vise.
3. To cut thin sheet material, “sandwich” the 
material between pieces of hardboard or ply-
wood, and clamp the layers together in order 
to reduce vibration and tearing of the mate-
rial.

MAINTENANCE

 IMPORTANT: Inspect the reciprocating saw, 

the on/off switch, and the cord for damage be-
fore each use. Check for damaged, missing, or 
worn parts. 

 CAUTION:

 

Be sure to switch power OFF and 

disconnect the plug from the receptacle during 
maintenance and inspection. Using cracked, 
deformed or damaged parts can result in seri-
ous personal injury.

The brushes are designed to give you several 
years of use. 
If they ever need replaced follow 
the instructions in this manual or return the 
tool to the nearest service center for repair.

INSPECTING THE SCREWS
Check for loose screws, misalignment or bind-
ing of moving parts, or any other condition 
that may affect the operation of the recipro-
cating saw. If abnormal vibration or noise oc-
curs, turn the reciprocating saw off immedi-
ately, and have the problem corrected before 
further use.
Using compressed air may be the most effective 
cleaning method. Always wear safety goggles 
when cleaning tools using compressed air.

INSPECTING THE CARBON BRUSHES
The motor employs carbon brushes which are 
consumable parts. Replace the carbon brush 
with a new one when it becomes worn to its 
wear limit. 
Always keep carbon brushes clean and ensure 
that they slide freely within the brush holders.
Using this reciprocating saw with a carbon 
brush which is worn in excess of the wear limit 
will damage the motor.

REPLACING CARBON BRUSHES
Remove the brush caps and carbon brushes. 
After replacing the carbon brushes, do not 
forget to tighten the brush caps securely.

 WARNING: Do not let brake fluid; gasoline, 

petroleum-based products, penetrating oil, 
etc. come into contact with plastic parts. These 
substances contain chemicals that can damage, 
weaken, or destroy plastic.

 WARNING: When servicing, use only iden-

tical replacement parts. The use of any other 
parts may create a hazard or cause damage to 
the product.

 WARNING: Use only accessories that are rec-

ommended for this reciprocating saw by the 
manufacturer. 
Accessories that may be suitable for one tool 
may become hazardous when used with an-
other tool.

 WARNING: Use only accessories that are 

recommended by the manufacturer for your 
model. Accessories that may be suitable for 
one tool may become hazardous when used 
on another tool.

 WARNING: Maintain tools with care. Keep 

cutting tools sharp and clean. Properly main-
tained tools with sharp cutting edges are less 
likely to bind, and are easier to control.

 WARNING: In order to ensure safety and re-

liability, all repairs should be performed by a 
qualified service technician.

SS950 manual.indd   13

07/09/16   9:35 a.m.

Содержание SS950

















Отзывы: