Urrea SI810 Скачать руководство пользователя страница 18

18

• NEVER PERFORM ANY OPERATION FREE-
HAND. Always place the workpiece to be cut 
on the miter table and position it firmly against 
the fence as a backstop. Always use the fence.

• NEVER hand hold a workpiece that is too 
small to be clamped. Keep hands clear of the 
cutting area.
• NEVER reach behind, under, or within three 
inches of the blade and its cutting path with 
hands and fingers for any reason.
• NEVER reach to pick up a workpiece, a piece 
of scrap, or anything else that is in or near the 
cutting path of the blade.
• AVOID AWKWARD OPERATIONS AND HAND 
POSITIONS where a sudden slip could cause 
your hand to move into the blade. ALWAYS 
make sure you have good balance. NEVER 
operate the miter saw on the floor or in a 
crouched position.
• NEVER stand or have any part of the body in 
line with the path of the saw blade.
• ALWAYS release the power switch and allow 
the saw blade to stop rotating before raising it 
out of the workpiece.
• DO NOT TURN THE MOTOR SWITCH ON AND 
OFF RAPIDLY. This could cause the saw blade 
to loosen and could create a hazard. Should 
this ever occur, stand clear and allow the saw 
blade to come to a complete stop. Disconnect 
your saw from the power supply and securely 
retighten the blade bolt.
• IF ANY PART OF THIS MITER SAW IS MISS-
ING or should break, bend, or fail in any way, 
or should any electrical component fail to 
perform properly, shut off the power switch, 
remove the miter saw plug from the power 
source and have damaged, missing, or failed 
parts replaced before resuming operation.
• ALWAYS STAY ALERT! Do not allow familiar-
ity (gained from frequent use of the saw) to 
cause a careless mistake. ALWAYS REMEMBER 
that a careless fraction of a second is sufficient 
to inflict severe injury.
• IF THE POWER SUPPLY CORD IS DAMAGED, it 
must be replaced only by the manufacturer or 
by an authorized service center to avoid risk.
• MAKE SURE THE WORK AREA HAS AMPLE 
LIGHTING to see the work and that no obstruc-
tions will interfere with safe operation BEFORE 

performing any work using the saw.
• ALWAYS TURN OFF THE SAW before discon-
necting it to avoid accidental starting when re-
connecting to power supply. NEVER leave the 
saw unattended while connected to a power 
source.
• TURN OFF TOOL and wait for saw blade to 
come to a complete stop before moving work-
piece or changing settings.
• THIS TOOL should have the following mark-
ings: 
a) Wear eye protection.
b) Keep hands out of path of saw blade
c) Do not operate saw without guards in place.
d) Do not perform any operation freehand.
e) Never reach around saw blade.
f) Turn off tool and wait for saw blade to stop 
before moving workpiece or changing settings.
g) Disconnect power (or unplug tool as appli-
cable) before changing blade or servicing.
h) No load speed.
• ALWAYS carry the tool only by the carrying 
handle.
• AVOID direct eye exposure when using the 
laser guide.
• SAVE THESE INSTRUCTIONS. Refer to them 
frequently and use to instruct other users. If 
you loan someone this tool, loan them these 
instructions also.

 WARNING: Some dust created by power 

sanding, sawing, grinding, drilling, and oth-
er construction activities contains chemicals 
known to cause cancer, birth defects or other 
reproductive harm. Some examples of these 
chemicals are; lead from lead-based paints, 
crystalline silica from bricks and cement and 
other masonry products, and arsenic and chro-
mium from chemically-treated lumber.
Your risk from these exposures varies, depend-
ing on how often you do this type of work. To 
reduce your exposure to these chemicals: work 
in a well ventilated area, and work with ap-
proved safety equipment, such as those dust 
masks that are specially designed to filter out 
microscopic particles.

 WARNING: To avoid serious personal injury, 

do not attempt to use this product until you 
read thoroughly and understand completely 
the operator’s manual. Save this operator’s 
manual and review frequently for continuing 

SI810 manual.indd   18

08/12/15   2:54 p.m.

Содержание SI810





























Отзывы: