-26-
Kits consists of hardware, mounting frame,
basket(s) and leveling bar(s).
Unpack bundles, separate and identify compo-
nents using the Parts Section, "Rolling Harrow
Attachments".
Set the MAXIMUS disk on the ground and block
against all movement.
WARNING! AlWAyS bloCK ThE DISK
fRoM RollING oR fAllING bEfoRE
PERfoRMING SERVICE. USE DEVICES RATED
foR WoRK PERfoRMED.
1. Install the jackstands (71402B) on the
mount weldment (71812B) and secure the
jackstands with the locking pin (97212).
2. Using a hoist and/or lifting devices rated
for 150 lbs. minimum, position the mount
weldment (71812B) along the frame tubes
of the MAXIMUS disk. Install clevis pins
(9950) and lynch pins (9951). Lower jack-
stands to ground.
oM-00195A
fIG. 3-11
3. Remove front U-Bolts (91434) and lock-
nuts (9800) from spring arm assemblies
(84763B). Position the spring arms on the
mount weldment according to the overhead
layouts for your unit. Secure with U-Bolts
and locknuts.
4. Remove U-Bolts (85620) and locknuts
(9801) from rear of spring arms. Position
basket(s) from spring arms according to
overhead layouts. Secure with U-Bolts and
locknuts.
washers (9404-025, flat washers (9405-088),
and hex nut (9394-010), (Fig. 3-10). Additional
adjustments may be necessary once the disk
is operating in the field. See the OPERATIONS
section for more details.
oM-04313
fIG. 3-10
oPTIoNAl SIDE ShIElD ASSEMbly
(bUNDlE #71809b)
ASSEMBLY
Unpack side shield bundle, separate, and identify
all components according to page 35 of the
PARTS section.
Side shields may be mounted in the LOW or
HIGH position, depending on the orientation of
the mounting bar (71808B). If you are uncertain
which position is needed, try the LOW position
first. Decide which position is desired and at
-
tach the mounting bars (71808B) to the shields
(71807B) with leg on mounting bar pointing up
(HIGH position) or down (LOW position). Secure
with 1/2-13 x 1 1/4 capscrews (9390-100) and
locknuts (9800).
Slide mounting bars over the outside frame
tube on disk. The bent leg of the side shield
should face the front and point in toward the
front disk gang. For initial set-up, place the
front of the side shield in-line with the front
edge of the front 2x6 frame tube on the disk.
Adjust the shield to have 4-6" lateral clearance
to the disk gange at the closest point. Secure
with 1/2-13 x 4 1/2 capscrews (9390-112), lock
ASSEMbly of
oPTIoNAl SINGlE RollING hARRoW ATTAChMENTS
(#72589b - 6fT; 72940b - 7fT; 71813b - 8fT; 72941b - 9fT; 72942b - 10 fT)
Revised 111808-2
Содержание MAXIMUS 100
