Unitron Gemscope 3075-GS Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 15

Unitron Gemscope 3075-GS Скачать руководство пользователя страница 5

GEMSCOPE

UNITRON

®

73 Mall Drive, Commack, NY 11725 • 631-543-2000 • www.unitronusa.com

5

INTRODUCTION

Congratulations on the purchase of your new UNITRON

®

Gemscope. UNITRON

®

Gemscopes are

engineered and manufactured to the highest quality standards. Your Gemscope will last a lifetime if used
and maintained properly. UNITRON

®

Gemscopes are carefully assembled, inspected and tested by our

staff of trained technicians in our New York facility. Careful quality control procedures ensure each
Gemscope is of the highest quality prior to shipment.

UNPACKING AND COMPONENTS

Your Gemscope arrived packed in a molded shipping carton.

Do not discard the carton

:

the shipping

carton should be retained for reshipment of your Gemscope if needed. Avoid placing the Gemscope in
dusty surroundings or in high temperature or humid areas as mold and mildew can form. Carefully
remove the Gemscope from the shipping carton and place the Gemscope on a flat, vibration-free
surface.

COMPONENTS DIAGRAM

Focusing Knobs

10x Eyepieces

Stereo Head

Stand

Top Fluorescent

Illuminator

Stoneholder

Main Switch

Magnification

Selection Knob

Base

Brightness Adjustment Knob

(Bottom Illuminator)

LED Illuminator

«
...
3
4
5
6
7
...
»

Содержание Gemscope 3075-GS
















Отзывы:

Нет отзывов