Unitron Gemscope 3075-GS Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 15

Unitron Gemscope 3075-GS Скачать руководство пользователя страница 14

GEMSCOPE

UNITRON

®

73 Mall Drive, Commack, NY 11725 • 631-543-2000 • www.unitronusa.com

14

TROUBLESHOOTING

Under certain conditions, performance of this unit may be adversely affected by factors other than
defects. If a problem occurs, please review the following list and take remedial action as needed. If you
cannot solve the problem after checking the entire list, please contact your local dealer for assistance.

Trouble

Cause

Remedy

Double images

Interpupillary distance is not correct

Readjust it

Diopter adjustment is not correct

Readjust it

Dirt appears in the view field

Dirt on the specimen

Clean specimen

Dirt on the surfaces of eyepieces

Clean eyepieces

Dirt on surface of objective

Clean objective

Dirt on stage

Clean stage

Image is not clear

Dirt on the surface of objectives

Clean objectives

Image is not clear while focusing

Diopter adjustment is not correct

Readjust diopter

Focusing is not correct

Readjust it

The focusing knob is not smooth

The focusing knob is too tight

Loosen it to a suitable position

The image is obscure because of the
head slipping down during
observation

The focusing knob is too loose

Adjust the tension on the focus
knobs

Lamp does not work

Bulb may be loose in socket

Remove bulb and reinsert

securely

Bulb has burned out

Replace the bulb

Fuse has burned out

Replace the fuse

Dirt on the stage obstructed the path
of light

Clean the stage

Lamp burns out frequently

Voltage from power supply is too
high

Use the brightness adjustment
knob to lower brightness

The bulb is not standard

Use the recommended bulb

Fuse burns out frequently

Voltage from power supply is too
high

Use the brightness adjustment
knob to lower brightness

Light flickers

Bulb needs replacement

Replace bulb

Bulb may be loose in socket

Remove bulb and reinsert

securely

«
...
12
13
14
15
»

Содержание Gemscope 3075-GS
















Отзывы:

Нет отзывов