manualshive.com logo in svg

Unitron Gemscope 3075-GS, Руководство пользователя, Страница: 3 / 15

Поделиться
Скачать
Unitron Gemscope 3075-GS Скачать руководство пользователя страница 3

 

GEMSCOPE 

 

 

 

 

UNITRON

®     

                          

73 Mall Drive, Commack, NY  11725  •  631-543-2000  •  www.unitronusa.com 

3

 

 
SAFETY NOTES 

 

1.  Open the shipping carton carefully to prevent any accessory, i.e. objectives or eyepieces, from 

dropping and being damaged. 

 
2.  Keep the instrument out of direct sunlight, high temperature, humidity, and dusty environments.   
 

 

 

3.  If any specimen solutions or other liquids splash onto the stage or any other component,  disconnect 

the power cord immediately and wipe up the spillage. Otherwise, the instrument may be damaged. 

 
4. 

LAMP REPLACEMENT -- CAUTION

:  the glass housing of the lamp may be extremely 

hot.  DO NOT attempt to change the lamp before it is completely cooled or without 
wearing adequate skin protection.   

 
5.  All electrical connectors (power cord) should be inserted into an electrical surge protector to prevent 

damage due to voltage fluctuations. 

 
6. 

FUSE REPLACEMENT

 -- For safety when replacing the fuse (ONLY replace with the 

same size, type and rating of original fuse), be sure the main switch is in the off position, 
disconnect the power cord from outlet, and replace the fuse.  Reconnect the power cord 
and turn unit on. 

 
7.  Confirm that the input voltage indicated on your Gemscope corresponds to your line voltage. The use 

of a different input voltage other than indicated will cause severe damage to the Gemscope. 

 

NOTE:  Always plug the Gemscope power cord into a suitable grounded electrical outlet.   

 

A grounded 3-wire cord is provided.   

 

 

 

 

 

Содержание Gemscope 3075-GS
















Отзывы:

Нет отзывов