background image

4

•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•

Read these rules and the instructions carefully. Failure to follow them will cause a hazard that could result in
death, serious bodily injury, and/or property damage.

Check your local codes. This installation must comply with their rulings.

Do not install this furnace in a mobile home or trailer.

Always connect this furnace to a chimney and vent to the outside. Never vent to another room or
inside a building.

Do not connect this furnace to an aluminum Type B gas vent. This is not safe and is prohibited by the
National Fire Protection Association Code. This furnace requires a masonry or listed factory built
chimney for residential type or building heating appliance chimney. Use a 6" diameter chimney or
larger, that is high enough to give a good draft. (See Page 8)

Be sure that if a masonry chimney is used, it is safely constructed and in good repair. Have the
chimney inspected by the Fire Department or an inspector.

Inspect chimney connector and chimney before and frequently during the heating season for any
deposit of creosote or soot which must be removed (see Chimney Maintenance, page 21.)

Provide air for combustion into the room where the furnace is located. If the intake is not in the same
room, air must have free access to the room.

CAST IRON PARTS MUST BE "SEASONED" TO AVOID CRACKING. BUILD ONLY SMALL FIRES
ON FIRST USE.

To prevent injury, do not allow anyone to use this furnace who is unfamiliar with the correct operation
of the furnace.

For further information on using your furnace safely, obtain a copy of the National Fire Protection
Association (NFPA) publication "Chimney's, Fireplaces and Solid Fuel Burning Appliances" NFPA
211. The address of the NFPA is Batterymarch Park, Quincy, MA 02269.

Keep the ashpit section free of excess ashes. Do not allow ashes to stack higher than the sides of the
ash pan.

DISPOSAL OF ASHES - Place ashes in a metal container with a tight fitting lid. Keep the closed
container on a noncombustible floor or on the ground, well away from all combustible materials. Keep
the ashes in the closed container until all cinders have thoroughly cooled. The ashes may be buried
in the ground or picked up be a refuse collector.

CAUTION - The special paints used on your furnace may give off some smoke while they are curing
during first few fires. Build small fires at first. The metal used in construction of the furnace and duct
work has a light coating of oil. This could give off smoke and/or odors from registers when furnace is
used for the first time. This should disappear after a short period of time. Once this burn-off has
occurred, it should not reoccur.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

RULES FOR SAFE INSTALLATION AND OPERATION

Содержание HOTBLAST 1200G





























Отзывы: