manualshive.com logo in svg

United States Stove Company 1602M, Инструкция по установке и эксплуатации

Поделиться
Скачать
United States Stove Company 1602M Скачать руководство пользователя страница 8

8

SPRING HANDLES

Attach the four(4) spring handles to the Feed/Ash Doors, 
Baf

fl

 e Rod, and Shaker Rod by twisting the springs 

counter-clockwise while applying pressure until you have 
screwed them approximately 3/4”-1” onto the rods.

(4) Spring Handles

(2) 

800 CFM Blower

(2) Gasket, 

Blower

(8) 

Tinnerman Clip, 1/4-20

(8) 

1/4-20 x 3/4 Bolt

(2) Conduit 

Assembly 

(5ft)

(1) 

Honeywell Limit Control

(1) Conduit 

Assembly 

(1ft)

(1) Junction 

Box

(1) 

Insulation (5” x 5”)

(1) Rocker 

Switch

(1) 

Romex Cable Clamp

(1) 

Fan Center Control

(3) 

73B Wire Nut

(1) 

74B Wire Nut

(1) Female 

Term. 

(blue)

(1) Female 

Term. 

(red)

(8) 

#10 x 1/2 Screw

DISTRIBUTION BLOWER & ACC.

1.  Remove all contents and insure that all components 

are present for assembly. See the part list below

2.  Begin by attaching the blowers to the unit. Insert a 

clip into each mounting hole in the furnace’s cabinet 
back. Be sure to install the gasket between the blow-
er and cabinet back. Insert the eight bolts provided 
and tighten. 

3.  Insert the adjustable snap-disc into the hole in the 

upper-left hand corner of the cabinet back. Attach us-
ing two of the #10 x 1/2 screws provided.

4.  Find the Snap-Disc box, the small black box shown 

on the left side in the illustration. Attach the shorter 
conduit assembly to the bottom of the box, securing 
it with the nut on the 

fi

 tting.

5.  Plug the wires onto the snap-disc (see wiring sche-

matic) and then attach the box to the back of the unit 
using four of the #10 x 1/2 screws provided.

6.  Next, mount the junction box and insulation using 

two of the #10 x 1/2 screws provided. Install the 5 x 
5 insulation between the cabinet back and junction 
box, with the foil side to the cabinet back. Attach the 

conduit assembly from the snap-disc box to the junc-
tion box as shown.

7.  If not already installed, snap the rocker switch into 

the top of the junction box.

8.  Attach the two longer conduit assemblies to the junc-

tion box and to each blower.

9.  Provide a 110v power supply and secure it with the 

cable clamp to the right  side of the box. Make all 
wire connections per the wiring schematic in these 
instructions using the supplied hardware. Mount the 
junction box cover.

(1) Spin Draft
(1) 3/8-16 Carriage Bolt
(1) 3/8-16 Lock Nut

SPIN DAMPER

Screw the spin draft onto the 3/8” x 2-1/2” carriage bolt 
followed by the 3/8”-16 lock nut. Then screw the spin draft 
and bolt into the Combustion Air Inlet allowing approxi-
mately 1/2” of the bolt to stick through into the threaded 
part of the tube. Secure the bolt in place with the 3/8”-16 
lock nut by tightening it against the tube bracket.

Содержание 1602M

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды