United Process Controls Oxyfire-LT Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 26

United Process Controls Oxyfire-LT Скачать руководство пользователя страница 15

United Process Controls, Inc.

Oxyfire-LT Installation/Operation Manual

15 |

P a g e

5

OXYFIRE-LT REPLACEMENT COMPONENTS

Warning

Disconnect the heater power before removing the sensor head cover. The mains voltage of this supply

is exposed when the cover is removed and is a potential shock hazard to maintenance personnel.

The Oxyfire-LT is designed for modularity and quick replacement of critical components. The sensor
has three key components that can be purchased separately for replacement on-site.



Sheath Assembly - this contains the protective sheath and stainless steel mount fitting



Electrolyte Assembly - this contains the electrolyte, thermocouple, and terminal block



Head Assembly - this is the manifold base with fittings and cap

For assistance with replacement component purchasing please contact MMI

«
...
13
14
15
16
17
...
»

Содержание Oxyfire-LT



























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды