United Electric Controls 1XTX00 Скачать руководство пользователя страница 20

Страница: 20 / 26

IM_1XTXSW-08

www.ueonline.com

TROUBLESHOOTING*

The relays and switches contained in the One Series are electronic. The on/off switch signal is produced by a transistor or a solid-state relay,

depending on the One Series model. Electronic switches cannot be properly tested with an ohmmeter. Instead, measure the voltage drop across

the switch connected to the intended load to determine if it is open or closed. A properly functioning One Series electronic switch will exhibit the

following voltage levels (see Table 8).

DISCRETE OUTPUTS TRUTH TABLE*

Set Point Reached?

IAW™ Fault?

SW1 & SW2 (as configured)

IAW™ Output

Normal State

Closed

Yes

Tripped State

Fail Safe Open

Yes

Tripped State

Closed

Yes

Tripped State

Fail Safe Open

Electronic Switch Voltage Levels

Signal Name

Location

Voltage Open (power supply
dependent)

Voltage Closed

SW1

TB2 (no polarity)

0 – 280 VAC or VDC

0 Volts (Nominal)

SW2

TB2 (no polarity)

0 – 280 VAC or VDC

0 Volts (Nominal)

IAW

OUTPUT

TB3-2 (+) & TB3-1 (-)

0 – 30 VDC

0 VDC (Nominal)

*Model 1XTXSW Only

LOST PASSWORDS

Contact UE Inside Sales at +1-617-923-6977 or go online at www.UEonline.com/UUC to obtain a unique unlock code. The Kanban number from

the product nameplate is required (see Figure 16).

Table 7

Table 8

THIS DOCUMENT IS PROPRIETARY

PROPERTY OF UNITED ELECTRIC CONTROLS.

UNAUTHORIZED USE IS STRICTLY PROHIBITED.

TOLERANCES ON FRACTIONS

±1/64

±1/2°

±0.010

±0.005

2 PLACE DEC 3 PLACE DEC ANGLES

Page 1 of 1

WARNING: AGENCY CRITICAL DOCUMENT.

NO REVISIONS WITHOUT CERTIFICATION

ENGINEER APPROVAL

NOTES:

LASER MARKED ON BLANK NAMEPLATE P/N 6211-751.

NAMEPLATE DIMENSIONS ARE 3.943" REF X 1.35" REF

FORMAT SHOWS FIXED TEXT AND GRAPHICS ONLY.

ANY VARIABLE TEXT SHOWN IS BETWEEN * MARKS.

E5537 ADDED PROTECTION METHOD CHECK BOXES.

6-12-15

E5530 UPDATED PER AGENCY REQUIREMENTS

6/9/15

E5453 FIRST ISSUE

5/14/15

2.25:1

DWG NO

UNITED ELECTRIC

CONTROLS COMPANY

WATERTOWN * MASSACHUSETTS

SCALE

TITLE

ORIGINAL DATE

DRWN

CHKD

APPD

DO NOT SCALE THIS DRAWING

DOC #: DE733010102 Rev B

ONE SERIES

NAMEPLATE

A-6211-847

5/14/15

6211-847

DESCRIPTION

DATE

DRWN

APPD

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES

REV.

ECN#

Figure 16

Kanban number and Date Code

Содержание 1XTX00



























Результаты поиска

Содержание 1XTX00

Отзывы:

Похожие инструкции для 1XTX00

Бренды по названию

Популярные бренды

United Electric Controls 1XTX00, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 1XTX00

Отзывы:

Похожие инструкции для 1XTX00

Бренды по названию

Популярные бренды