United Electric Controls 1XTX00 Скачать руководство пользователя страница 18

Страница: 18 / 26

IM_1XTXSW-08

www.ueonline.com

HART Commands Cont.

Command

Description

Type

Write Number of Response Preambles

Common Practice

Lock Device

Common Practice

Read Lock Device State

Common Practice

140

Write Field Stats Information

Overwrites the Max and Min values from the device.

Device Specific

141

Read Field Stats Information

Reads the current Max and Min values from the device.

Device Specific

221

Write Protect Enable/Disable, Modify Password

Allows write protect mode to be enabled/disabled and allows editing of the

device password.

Device Specific

222

Read, Write Protect Status

Reads the write protect status of the device.

Device Specific

223

Write Trip Counters

Writes an unsigned 16-bit integer between 0 – 9999 to the trip counters associ-

ated with switch 1 and switch 2 (Trips 1 and 2).

Device Specific

224

Trips 1 and 2

Reads the value of the trip counters associated with switch 1 and switch 2 (Trips 1

and 2). The number is an unsigned 16-bit integer between 0 – 9999.

Device Specific

225

Manual Reset

Resets one or more switches that are in the latched state.

Device Specific

226

Read Switch Latch Status

Reads the latch status of one or more switches.

Device Specific

244

Write Switch Configuration

Write Switch Number, Mode, Set Points, Deadbands, Latch Settings, Trip Delay

Settings

Device Specific

245

Read Switch Configuration

Read Switch Number, Mode, Set Points, Deadbands, Latch Settings, Trip Delay

Settings

Device Specific

246

Write Plugged Port Settings

Enable/Disable Plugged Port Feature, set plugged port time and threshold.

Device Specific

247

Read Plugged Port Settings

Read Plugged Port time and threshold.

Device Specific

248

Write Offset and Span

Writes offset and span values for the purpose of calibration to the offset and

span menu entries.

Device Specific

249

Read Offset and Span

Reads offset and span values from the device.

Device Specific

Table 5

Содержание 1XTX00



























Результаты поиска

Содержание 1XTX00

Отзывы:

Похожие инструкции для 1XTX00

Бренды по названию

Популярные бренды

United Electric Controls 1XTX00, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 1XTX00

Отзывы:

Похожие инструкции для 1XTX00

Бренды по названию

Популярные бренды